E4OD Front Pump Bushing (not the seal) - FSB Forums
 
LinkBack Thread Tools Display Modes
post #1 of 4 (permalink) Old 07-18-2012, 11:02 PM Thread Starter
Registered User
 
Join Date: Sep 2011
Location: Rugby, ND
Posts: 282
Bronco Info: 96 White 351w D44-TTB, 8.8, E4OD with Punisher Valve Body
Exclamation E4OD Front Pump Bushing (not the seal)

hello,
to introduce myself I got my first bronco about a year ago for my 16th birthday and soon after discovered this site and would like to say thanks for all the info on here.
And now to my question. I have recently started having problems with it i had a fuel pump go out which caused a chain reaction that ended up with my tranny nearly overheating which blew out my front pump seal. I removed my tranny and bought new seals for the front pump. that was all straight forward thanks to many other threads on that. my problem occurred when i went to replace the bronze? bushing just behind the seal. it appears to be installed backwards of how it should be. So I guess what i'm asking is how do I remove the old bushing and which direction should the new one be installed???
thanks in advance oh ya and ive searched
the pic is not mine (its is what i think is the correct orientation) on my pump the bushing is upside down from what this is which i think is wrong?
Giddy-Up is offline  
Sponsored Links
Advertisement
 
post #2 of 4 (permalink) Old 01-15-2013, 11:58 PM Thread Starter
Registered User
 
Join Date: Sep 2011
Location: Rugby, ND
Posts: 282
Bronco Info: 96 White 351w D44-TTB, 8.8, E4OD with Punisher Valve Body
Just to add an update for those who search. it has been several months now problem free not a drop of fluid, I ended up bringing the front pump to a tranny shop and as it turns out the bushings orientation in the above image is incorrect. the shop seemed familiar with the E4OD problematic front seal and enlarged the drain back hole, which is just under the lip of the seal. hope this helps out someone
Giddy-Up is offline  
post #3 of 4 (permalink) Old 01-16-2013, 05:23 AM
Thanks 351w500
 
LarryP's Avatar
 
Join Date: Mar 2005
Location: Northcentral,CA.Twain Harte, up here in the mountains
Posts: 5,458
Bronco Info: 88 Centerion 460 Dana 60/10.25 78 Bronk Cromo shafts,Detoit 4.56's lift 7" Deavers 38's 9"rear disk
That pic is wrong cause some times when a pic is taken the image will get flopped or reversed. Good job on having the bushing changed, alot of ppl over look that when putting a new seal in.


I take Prayer Requests. God Bless
LarryP is offline  
post #4 of 4 (permalink) Old 01-16-2013, 04:26 PM Thread Starter
Registered User
 
Join Date: Sep 2011
Location: Rugby, ND
Posts: 282
Bronco Info: 96 White 351w D44-TTB, 8.8, E4OD with Punisher Valve Body
thanks, i noticed when i was replacing the seal that the bushing was scored so i decided to replace but thankfully the torque converter was just fine and actually appeared very new
Giddy-Up is offline  
Reply

  FSB Forums > Bronco Discussions > Noobie Bronco Tech Questions. Flame free zone!

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the FSB Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself. DO NOT USE Gmail.com accounts. If you only have a Gmail.com email please contact the administrator here

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome