So far, I've built pretty much everything, except a strictly prerunner, for every generation of Bronco. Here's just a few examples of what I've done -

I've built two of these, so far -
http://www.supermotors.org/getfile/106340/fullsize/Davids-bumper-2.JPG

Not a very clear picture on this one, is it? This one just got sent to TX
http://www.supermotors.org/getfile/246879/fullsize/bumper.jpg

http://www.supermotors.org/getfile/246880/fullsize/bumper-side.jpg

The idea for this one -
http://www.supermotors.org/getfile/111369/fullsize/front.JPG

was borne from this one - picture, and idea, courtesy of Crazed
http://www.supermotors.org/getfile/88464/fullsize/Welding%20and%20bending%20for%20Todd%20099.jpg

I only have a few pictures of rear bumpers I've built -

http://www.supermotors.org/getfile/38925/fullsize/4x4bumper-display.JPG
http://www.supermotors.org/getfile/38939/fullsize/LR-lift.JPG

http://www.supermotors.org/getfile/168120/fullsize/after2.jpg

I know there are more, but I can't seem to find them. All bumpers are shipped via truck freight, by Saia, Inc, either to a business address, or can be picked up at the terminal. I offer three payment plans:
1) half down, with the balance, plus shipping, due upon completion, within 14 days
2) half down, with the balance, plus shipping, due in two payments, within 30 days
3) payment in full, with the shipping due upon completion, within 30 days

If the orders haven't paid for, within the 30 days of completion, then I regret to inform that customer, that the entire order will be forfeited, with no chance on reimbursement. I hate to have to do that, but I just do not have the space for storing orders

can you build off of autocad/solid works drawings?

I sure can. You have something in mind?

a rear that would wrap around the sides and be supported to the frame, plus a reciever. i also have a design for some unique sliders on my computer, i'd have to figure what is the priority. i haven't finalized anything, but i thought i'd ask. its sad, but during school money is actually easier to come by than having time and tools.

Shit i wish you lived close id love a double tube bumper for the front that raps around flush with the body.. I cant find them for 94 broncos anywhere on the internet.

Zach, that would be no problem at all

Bm - I can still help you out. I offer three payment plans, to make it as easy as possible, for those that are wanting a bumper, but can't afford to front all the money all at once - mind you, no matter which plan is chosen, the bumper isn't sent, until the balance, and shipping, is paid in full ;)

Can you build one for the front like toddac's I like that one it is perty. if not i like the first one on there can you tell me how much it is?

Thanks

do you give a frequent buyer discount? :brownbag

The one on Todd's truck will sell for $425. The first one shown sells for $850

How about a rear bumper like the one second from last with a receiver and clevis hooks? 90 bronco

With a receiver, and anchor points, the cost is $350, made from 4 x 4 x .188" box tube, with .250" mounting plates

How 'bout just hooks, no hitch. shipped to 63011 Ballwin, MO?

Can you do the first bumper style with a receiver? ala Big Mikeish

Can you add a tire mount to either bumper?

The one on Todd's truck will sell for $350. The first one shown sells for $750

I can get you rough dimensions as well as suggest that you make it slightly wider. Otherwise I'd say $350 is an awesome deal.

Sorry Joe, somehow, I missed your question - frequent buyer discount? Yeah, I think I can make that a possibility

wookie, same rear bumper, two anchor points, cost is $285. You ARE referring to the one with the hi-lift jack, right? That's the same one as the bumper directly above it - simple, tapered, but built to accomodate the hi-lift

Bill, yes, and yes

Todd, being 75" wide, I'm really not interested in making them any wider, but thanks for the suggestion

i too am wantin the big mike-ish style with a built in reciever ala this one:

http://fullsizebronco.com/forum/attachment.php?attachmentid=327&stc=1&d=1105324089

cept with no air.

maybe we can set sumthin up like last time.(cept have it go my way this time :duh)

did you move closer or further from me? i dont remember.

Joe

I was thinking of something like this for the front.

http://www.superford.org/getfile.php?id=111907&toggle=fullsize&f=DSCF0023.JPG
http://www.superford.org/getfile.php?id=111891&toggle=fullsize&f=DSCF0007.JPG
http://www.superford.org/getfile.php?id=111908&toggle=fullsize&f=DSCF0024.JPG
http://www.superford.org/getfile.php?id=111894&toggle=fullsize&f=DSCF0010.JPG

I think it could stand to be a little narrower from top to bottom, and I would want the sides cut further forward. Other than that, I think I've found a winner.

How spendy are we talking for something similar?

i too am wantin the big mike-ish style with a built in reciever ala this one:

http://fullsizebronco.com/forum/attachment.php?attachmentid=327&stc=1&d=1105324089

cept with no air.

maybe we can set sumthin up like last time.(cept have it go my way this time :duh)

did you move closer or further from me? i dont remember.

Joe

whoa weird double post magic

Joe, the picture isn't showing up :shrug

Derrick, one similar to that would be about $650. My second picture sold for that much, and the one you're wanting is fairly close to the same design

Just built a bolt-on prerunner bumper this weekend, for BadBlueOval

http://www.supermotors.org/getfile/249596/fullsize/prerunner-bolt-on.JPG

http://www.supermotors.org/getfile/249597/fullsize/013bdd07301e.jpg

http://www.supermotors.org/getfile/249599/fullsize/1763f182752c.jpg

http://www.supermotors.org/getfile/249603/fullsize/prerunner-bolt-on2.JPG

Naturally, this is built to bolt onto the stock front bumpers, for the 78-9 years. When I receive Travis' Bronco in a couple weeks, I'm going to see about building one for the 87-91 years.

Price for this one, is $325, includes one pair of light tabs. Shipping will be easy... dang thing only weighs about 20-25lbs

Joe, the picture isn't showing up :shrug

i pirated the link for the pic from the bike mike thread.
i can see it.

:shrug

Wierd, I still can't, but now I know what you're talking about. While I won't copy anyone's design, I can build something similar. I have another design in mind. When I get around to it, perhaps I'll post a drawing of it, see what you think

Hey, David. When you do one like this for the 87-91s be sure to post some pics. I'd like to get one. I can't find anyone else (company) that makes them. :beer

Just built a bolt-on prerunner bumper this weekend, for BadBlueOval

http://www.supermotors.org/getfile/249596/fullsize/prerunner-bolt-on.JPG

http://www.supermotors.org/getfile/249597/fullsize/013bdd07301e.jpg

http://www.supermotors.org/getfile/249599/fullsize/1763f182752c.jpg

http://www.supermotors.org/getfile/249603/fullsize/prerunner-bolt-on2.JPG

Naturally, this is built to bolt onto the stock front bumpers, for the 78-9 years. When I receive Travis' Bronco in a couple weeks, I'm going to see about building one for the 87-91 years.

Price for this one, is $325, includes one pair of light tabs. Shipping will be easy... dang thing only weighs about 20-25lbs

Hey, David. When you do one like this for the 87-91s be sure to post some pics. I'd like to get one. I can't find anyone else (company) that makes them. :beer
Rest assured, I will be posting pictures

When I get it put on my 78 I will post pics.

Took all of 5 minutes, to get it mounted :twotu:

http://www.supermotors.org/getfile/252352/original/bryans-prerunner-bumper.jpg

http://www.supermotors.org/getfile/252354/original/bryans-prerunner-bumper-sideview.jpg

Thanks again Dave.I got it all cleaned up,painted and put back on.I'll post pics later today.

Funny, I was just wondering how that'd look, with a good polishing, and about 4-5 coats of clear coat paint :shrug

I cant get the pics to download off my digi cam.I painted it to match the Bronco and put about 4 coats of paint and clear on it.Looks awsome.

updated pics badblueoval?

Here's a pic of it all painted and clear coated.

http://www.supermotors.org/getfile/253497/fullsize/DCP_0020.JPG

I am looking for Big Mike-ish type with a tire carrier, hitch, and clevis mounts.

:smokin: Dam nice rig.Really like the add on.

Me thinks I will make me one.:twotu:

Dang, Bryan, that looks better with the paint on it. :thumbup

I am looking for Big Mike-ish type with a tire carrier, hitch, and clevis mounts.
Hang tight, I'm STILL building one for runnin&gunnin. His will include a different latch (than the one that blew apart on Blaze), and will use a gas strut, to hold the tire carrier open

Well Dave I will have to say it held together pertty good last night.I hit a deer on my way to work and all it did was scrape some paint off.I hit him doing 60mph and ran over him.No damage to the bumper nor the Bronco.

Those DAMN DEER (just like it's written in my sig).

Glad you are ok.:thumbup

If I wasnt late to work,hense the 60mph,I would have went back to look for him.I knew it was a buck because all I saw was horns before I hit him.

Hang tight, I'm STILL building one for runnin&gunnin. His will include a different latch (than the one that blew apart on Blaze), and will use a gas strut, to hold the tire carrier open

just the bumper w/ hitch and clevis mounts for me......but can you set the bumper up so you can build the carrier later and we can just attach it?

Well Dave I will have to say it held together pertty good last night.I hit a deer on my way to work and all it did was scrape some paint off.I hit him doing 60mph and ran over him.No damage to the bumper nor the Bronco.
Get pictures! You didn't clean it already, did you?


Joe, not really, because of the way the hinge is made. If you're adament (sp) about it, I could, but the tire carrier would about 2-3" beyond the bumper... not really the makings for a good looking bumper, IMO. Ideally, the two are built together

k

and here i was thinking that with the bumper just bolted onto the stock one, that it wouldn't be very strong. i stand corrected after the deer incident. too bad you couldnt have gone back and got the sumbitch. :twotu:

Thanks for the compliments, guys, but I do need to keep this thread limited to questions about the bumpers I build. Thank you

No pics,and yes I already cleaned it up.

how much would a bumper like the on ein theis pic run me??

http://www.photodump.com/direct/89StockBronc/bumperidea.jpg


its just something i wipped up in zmod a few min ago. exactly the same except maybe for some front attatchemt points for a 87-91 body style. please excuse the fact that its not perfect

Right about $450

http://www.superford.org/getfile.php?id=111894&toggle=fullsize&f=DSCF0010.JPG


i'd like the exact type, same dimensions. it's close to your sec pic in the first post, but not quite. i like the drop down center and the integrated winch. can you make it exact?

i was wondering if you are willing to make one just like this one for me and if the cost would still be $650-ish?


thanks,
mike

Patented ideas and designs, or not, I make a serious effort in trying not to copy anyone's designs. If that's what you're wanting, all I can do, is say I'll ask for permission to build that. If permission is not granted, I can modify one of my other bumpers, to come as close to what you're wanting, as possible. One definite change, will be the anchor points... I don't use D-rings, but rather weld-on anchor points, in which you'll use your clevis shackle for any recoveries

how much would a bumper like the on ein theis pic run me??

http://www.photodump.com/direct/89StockBronc/bumperidea.jpg


its just something i wipped up in zmod a few min ago. exactly the same except maybe for some front attatchemt points for a 87-91 body style. please excuse the fact that its not perfect

looks almost exactly like my Warn classic winch bumper. i plan on keepin the winch center section but was gonna ask David for some ideas on modding the sides for more clearance/protection.

or just some other design for the front. i want clearance mostly, good recovery attachments and winch mount.

whatcha think Dave?

If you're wanting more clearance, start from the beginning, and let's mount that winch as close to behind the grill as pissible - much the same as Todd and Tim, had me build for Todd's bronco

which is Todd? show me.

picture courtesy of Crazed
http://www.supermotors.org/getfile/88455/fullsize/Welding%20and%20bending%20for%20Todd%20079.jpg

http://files.photojerk.com/DeadlyPapercuts/bumperfordavid.jpg


how about this one david?

Sorry Mike, I only see the infamous red X. If you want, you can email it to me - diamondbackmotorsports@gmail.com

that's odd because i see it now......

after further research, my file hosting site's hard drive crashed, leaving the infamous red x. it should be good now that it's back up nd i reloaded the pic. now if i can get my ako email to attch the damn thing then i should be alright.

but how much did David give a quote for the rear bumper you want cableguy?

What are you asking him for? Offering to build him one?

Mike, I see the picture now... the price is the same, and includes onepair of light tabs. Any more, are ordered as an option, at $25/pr

me build one...no. just wanted to know the price cause I am interested in one like that as well.

Alright, well, the base rear bumper is $225. Options for that are: Anchor points - $75/pr, recessed hitch - $75. The tire carrier is $325. . Options for that are: auxilliary light mount - $15, CB antenna mount - $15, gas can mount - $65

Im lookin to have a bumper made up exaclty like this for a 1995 F150, though with out the hoop and it dont have to have the recessed plate-

http://fordtruckworld.tenmagazines.com/gallery/Fabed4d88/568847.jpg
http://fordtruckworld.tenmagazines.com/gallery/Fabed4d88/568855.jpg

around how much would something like that cost???

:stupid

but maybe a winch mount.

Building one like that would be closer to $750

Just shipped this to runnin&gunnin -

http://www.supermotors.org/getfile/265450/fullsize/11-17-05.jpg

I might have to copyright this idea... Works like a F'in charm :twotu:
http://www.supermotors.org/getfile/265452/fullsize/11-17-05-2.jpg

Not too bad, I don't think..
http://www.supermotors.org/getfile/259569/fullsize/ed97d11552b4.jpg

I need one of those for my 79. PM me a price shipped to 19446 if you could.

What is the bumper going for? The one to runnin&gunnin....

As that bumper sits, loaded with options - gas can mount, recessed hitch, anchor points, CB antenna mount, the package sells for $585, plus shipping, to a business address

Thats a frickin awesome bumper but I would have pay out the a$$ to ship across the US. Let me see what I can get done locally and then get back to you.

I do offer two payment plans (used to be three):

half down, with the balance, plus shipping, due upon completion

half down, with the balance, plus shipping, due within 30 days of completion - altho, everyone's been able to pay the balance soon after I finish, because of how long it takes me to fill an order

If you can provide me with a zip code for a business address, I could, at least, get you a shipping estimate

Hey David, Id like to pick your brain a bit here. Whats the BIGGEST HEAVIEST bumper you have made for a newer FSB? Do you know how much it weighed in at? Im trying to do some figuring up.

Thanks!
Kyle

PS, Ill be saving up for one of those loaded rear bumpers!

Thats super nice David. Great job. someday i will have one of those.

biggest and heaviest? That's hard to answer, since I've been building bumpers for these guys, for almost two years now (off and on, really). Most large bumpers come in at around 150lbs. That rear bumper and tire carrier weighed in close to 165lbs

I was wondering what the price of a rear bumper like the one above would be, but much simpler in design, no tire carrier, no hitch, just the plain bumper, with the 2 welded shackle mounts. Shipped to Pa Zip code 19135. It would be a commercial address (were I work) And I would pay with paypal. Please let me know when you can, and approximately how long it would take. I know you are busy and thank you in advance for your time

The basic rear bumper, with just the anchor points, comes to $265, and shipping comes right close to $95

The basic rear bumper, with just the anchor points, comes to $265, and shipping comes right close to $95

Can that bumper be cut to where it fits the countours a little better?

Similar to this.
http://www.supermotors.org/getfile/207385/fullsize/000_0328.JPG
http://www.supermotors.org/getfile/207991/fullsize/000_0332.JPG

It might already, but it's hard to judge from the pics, so I figured I'd ask.

I'm wanting something like this, with 4 light tabs on top (Or two on top and two on the bottom). I have a tube grill so I can't use the setup where two bars attach to my radiator support. I know you don't care to copy right so you can add a lil' sumin sumin to state that it came from you.

(Mainly looking for price quotes)
Thanks,
Zane
Oh yeah, it's for a 78


http://broncograveyard.com/images/catalog/zoom/BUM2000FRONTA.JPG

I didn't do that, simply because the tire carrier covers practically everything. But, if just the rear bumper was ordered, I could certainly accomodate that

[FONT="Times New Roman"]I'm wanting something like this,...
I assume you're wanting the winch mount, also? I've given that design alot of thought, and while it's a good enough bumper by itself, I feel it can be brought closer to the grill, so for the most part, that's going to be the major change I make. Other changes will include a full winch mounting PLATE, and a different gusseting at the bumper wings. So, because of the extra material required, and the changes made, the price is going to be $695

I like the distance of the bumper, but I never plan to run a winch.

That will bring down the price to about $595, then

The basic rear bumper, with just the anchor points, comes to $265, and shipping comes right close to $95

How long would it take to make? I know you are working on other projects is why I ask. I could send $200 VIA paypal right away, the rest soon

I'm scheduled until after the new year. I have a cargo rack, front leaf spring crossmember, rear bumper/tire carrier, and possibly 3 pre-runner style winch bumpers, all going on right now. Unless you really don't mind parting with it, and letting it sit in paypal for a couple months, I would discourage sending any money just yet,

Okay, just let me know when it is my turn

:popc1:

I'm very interested as well, out of all the pics in this thread i like the bumper on the box bronco the best!! If i did sign up for bumpers, i would need a front bumper similar to that one, and a rear bumper with tire carrier big anough to house a 42. Or a 44 just to be safe :-) I dont know if this has been asked, but what kinda of guarantee's do you have?

guarantees? :toothless These are offroad, aftermarket products. I don't offer any guarantees, or warranties, for anything I build.


... the bumper on the box bronco. Umm, which one is that? :shrug

I can build the rear bumper's tire carrier to hold your 44, but it's going to cost extra. I try to suggest limiting my carriers to no larger than 38s. Any bigger than that, and I have to build the carrier's a bit differently

Hey David,

I asked you b4 about making a bumper that fit the contours of the rear better. You said that the one that was built for runnin & gunnin was made wider so the swing away tire carrier would fit.

Would it be possible to design a bumper similar to runnin&gunnin's, that fit the rear contours better(like the bottom pic from Mike2), but instead of having a swing away tire carrier, have a fold down tire carrier, that mounted right about where your attach fittings mount? That way, it could fold down--out of the way of the tailgate, plus for taller lifts(like I'm working on) it would bring the spare down to a more reasonable height.


http://www.supermotors.org/getfile/265450/fullsize/11-17-05.jpg

http://www.supermotors.org/getfile/207991/fullsize/000_0332.JPG

So, you'd rather lift 130+ lbs of tire and carrier, rather than swing it, just to get it out of the way of the tailgate? I also don't see how the fold-down carrier will bring the tire down to a more reasonable height. What am I to do? hang the tire from the bumper??? :shrug

So, you'd rather lift 130+ lbs of tire and carrier, rather than swing it, just to get it out of the way of the tailgate? I also don't see how the fold-down carrier will bring the tire down to a more reasonable height. What am I to do? hang the tire from the bumper??? :shrug


It made sense in my head, but ya good point.:brownbag

It made sense in my head, but ya good point.:brownbag
That just earned you a new title :goodfinge


Alright, getting back on track ...
While I could still design the carrier to accomodate that, it would cost way more than it's worth. So, because of that, I'm just going to stick with using a gas strut for the swing-away

As I am still waiting my turn for a super rear bumper, I did have one more question. How wide are the tabs the clevis hooks attach to? I am hoping they are an inch wide since I just picked up 4 clevis, powder coated in black with a 1 7/8" Gap. I am really hoping my turn comes soon :popc1:

Yes, the anchor points are 1" wide. You turn is coming around about as fast as I can make it happen. Finishing a rear bumper/tire carrier now, have two more orders, then it could be you

And thanks for your patience :thumbup

I stole these pics form Ironclad. Do you think that runnin&gunnin bumper is going to stay as close to the edges as this one?
http://www.supermotors.org/getfile/185375/fullsize/new_1a.jpg
http://www.supermotors.org/getfile/185380/fullsize/new_2a.jpg
http://www.supermotors.org/getfile/185374/fullsize/new3.jpg
http://www.supermotors.org/getfile/185377/fullsize/new4.jpg

That's what I'm really looking for, I just didnt know if it'd work with your spare tire carrier design.

I like the look of your swing away better tho.

What do you mean, "stay as close to the edges"? You mean are the ends of the bumper going to be where Ironclad's are? Yes

How could it not work with my carrier design? You mean is the latch and the catch for it going to get in the way of the tailgate? No, it won't

[QUOTE=derrick36]I was thinking of something like this for the front.

http://www.superford.org/getfile.php?id=111907&toggle=fullsize&f=DSCF0023.JPG
http://www.superford.org/getfile.php?id=111891&toggle=fullsize&f=DSCF0007.JPG
http://www.superford.org/getfile.php?id=111908&toggle=fullsize&f=DSCF0024.JPG
http://www.superford.org/getfile.php?id=111894&toggle=fullsize&f=DSCF0010.JPG

I agree with derrick. Im looking to go to something like this. Just a little narrower. Still around 650? How bout the bumper like you built with the swing out tire carrier,shackle mounts, and antenna mount? Package deal? Obviously all for an 86.If you call me about the electrical this weekend, we can talk then, or pm me ill call you.

Thanks dave!!

Josh

Josh, if you're going to be up and around in an hour from now (note, the time in my reply), then lte me know, and I'll PM my number

How difficult would it be to build something very similar to this pic:

http://img258.imageshack.us/img258/8365/fordbumper026wo.jpg

I have a much larger image if needed.

I realise you say you will not copy a design, and that's cool, but would you be able to do something very similar to this?

This will be going on the front of a 93 F150. I would like to get a rear with a similar style, as well as some tube sliders, but am mainly interested in the front bumper for now.

I'd like to know a total guestimate on the build, as well as timeframe, thanks.

Shipping would be to 75023, or Dallas/Ft. Worth, TX area.

W/o having a truck here, to model from, that style will be difficult to build for. Those anchor points appear to be using the frame horn. GUESStimated cost on that would be about (!) $550, plus $125 for shipping. Timeframe? I hope you're not in a hurry, I have two orders now, and a potential two more in waiting. It would be closer to the end of february, before I would accept anymore orders.

W/o having a truck here, to model from, that style will be difficult to build for. Those anchor points appear to be using the frame horn. GUESStimated cost on that would be about (!) $550, plus $125 for shipping. Timeframe? I hope you're not in a hurry, I have two orders now, and a potential two more in waiting. It would be closer to the end of february, before I would accept anymore orders.



Thanks for the quick reply.

I kinda figured it'd be difficult to make without having the actual truck to use as a guide, but you know your abilities more than I do. I'm definitely in no hurry for anything, and that price is a bit over my budget as it stands currently.

you may have noticed, I do offer payment plans, for orders over $500. Might be something to keep in mind

you may have noticed, I do offer payment plans, for orders over $500. Might be something to keep in mind


I did notice, and think that's cool that you offer that option. I think you're the only person I've seen offering such a service that does not go through a credit service. :thumbup

Just to give you an idea, my ideal budget for a front bumper is in the 300-350 range before any necessary shipping costs. So 600-675 range is kinda stretching it a bit, but I am definitely keeping you in mind, especially with the payment options you offer. We'll just have to see how good the next two months are for me financially...

http://www.superford.org/getfile.php?id=111907&toggle=fullsize&f=DSCF0023.JPG


Or you could hack 4 inches out of the middle of that bumper and get something that looks good.

http://www.fordtruckworld.com/gallery/86RangerSTX/609763.jpg

I did notice, and think that's cool that you offer that option. I think you're the only person I've seen offering such a service that does not go through a credit service. :thumbup
That's because I don't ship, until I get paid in full ;)

David,

Can you do something basic for the rear......just need "a" bumper back there, got the spare tire carrier on the truck, so i don't need something extravagant, maybe some pull points. Ideas? and How much?

And for the front i would like something just as basic, that follows the curves of the OEM bumper, with a winch mount?

Let me know.

Rob

You betcha. In fact, I'm building a rear bumper just the way you're wanting, for Accessory Man. I should be done with it by the middle of next week

The front bumper can be built to match quite easily. But, before I commit to that one, I'm trying to design it, so a winch can actually be used, and not get pulled from the frame. And I need to design it, so a guy with basic tools can install it at home. I have a feeling that alot of the design, will come from Rafa's :shrug

You betcha. In fact, I'm building a rear bumper just the way you're wanting, for Accessory Man. I should be done with it by the middle of next week

The front bumper can be built to match quite easily. But, before I commit to that one, I'm trying to design it, so a winch can actually be used, and not get pulled from the frame. And I need to design it, so a guy with basic tools can install it at home. I have a feeling that alot of the design, will come from Rafa's :shrug

The frame on a 92-96 really sucks. I couldnt think of a good way with out welding all new brackets. The stock brackets are useless and shouldnt be used if at all possible. I'd highly recommend a weld on bracket

You betcha. In fact, I'm building a rear bumper just the way you're wanting, for Accessory Man. I should be done with it by the middle of next week

The front bumper can be built to match quite easily. But, before I commit to that one, I'm trying to design it, so a winch can actually be used, and not get pulled from the frame. And I need to design it, so a guy with basic tools can install it at home. I have a feeling that alot of the design, will come from Rafa's :shrug

Let me know a price when you get the chance. I have all the recovery gear now, just need a winch.

Basic = Cheap as possible too. Don't want to toss all my cash at a bumper.

I kinda like how the Bronco Air Front bumper looks and mounts, reinforced all the way back to the sway bar. I am pretty sure he uses it often with the M12000 winch, I dont think he has had any problem.

I am very excited about my rear bumper and will do my best to post pics of the install as soon as it is done!

I kinda like how the Bronco Air Front bumper looks and mounts, reinforced all the way back to the sway bar. I am pretty sure he uses it often with the M12000 winch, I dont think he has had any problem.

I am very excited about my rear bumper and will do my best to post pics of the install as soon as it is done!

You got pics of that? I've always wondered what he does

Somewhere I think I do have some pictures, I have been trying to get in touch with him all week to get a finalized shipped price and send him a deposit for one

Somewhere I think I do have some pictures, I have been trying to get in touch with him all week to get a finalized shipped price and send him a deposit for one
I really wanted a broncoair bumper but couldnt foot the bill, oh well I'm happy with what I've got now

OK, getting back on track here...

Rob, the rear bumper sells for $265, plus shipping. The front will likely get closer to $400-450, depending on how complex the design ends up being

how long would it take?

The rear bumper will take 3-5 days. The front will take a bit longer... a week; week and a half. My turn around will be much quicker, since taking DiamondBack fulltime now

$725 total for both bumpers.

Anyway we could split that into 4 payments? I know you like the two thingy, but money is going to get real tight around here. (four payments of about $185.00)

I take it things fell through with your friend and building that house?

You know that saying? - "if it sounds to good to be true..." - yeah, I think I got suckered

I could possibly work something out. Whenever you're ready to get started, shoot me an email - diamondbackmotorsports@gmail.com

Guys just to kick in here, sorry I have'nt been around much lately but f"in work ya know. Dave does very nice work and is a stand up guy, money is important but quality comes first. Dave has had my permission to copy my design for years and you wont go wrong getting anything he builds.

bigmike

Thank you, Mike, your support means alot. And your permission means just as much :thumbup

David,
what is the length and width of your bumpers? can you make a bumper with an inset for a license plate? i am wanting one of your bumpers with a inset plate on the drivers side,2 inch reciever in center and maybe an anchor point or light on the passenger side. also wanting it to work with a hi lift jack.
Let me know what you think,
Kenny

75" wide, built with 6 x 4 rectangle tubing. I don't do any inset license plates, but rather weld in 1/4 - 20 couplers, to bolt the license plate too, with lights on both sides. I can't include a Hi-Lift mount, with the anch points. Not W/O a tire carrier. All said and done, the rear bumper comes to $390, plus shipping to a business address

I had not planned on license plate provisions myself, I have already made arangements to mount my license plate, and I have my hitch wiring, and tag lights ready to go just so when my bumper arrives it will be on the truck same day, painted and legal. I alrady have primer, paint, clevises, shiny new plate fram and smoke cover, security bolts (which I planned on tapping holes for in the bumper), and a nice freshly painted pintle hitch to fill in the ugly empty hitch since I won't need the clevis in there anymore.

I am very excited :toothless

Sooo, you don't want me to install the couplers, or drill for the license plate lights? Not a problem :thumbup

thats correct, just a basic bumper, and by saving you from having to do all that, you should be done like 20 minutes sooner :histerica So I should get the bumper like 20 minutes sooner too!!!!!

:toothless

Theoretically, huh? :goodfinge



alright, lunch's over, back to work for me ...

on the Hi-Lift i meant being able to use the jack on the bumper like you have posted in a pic on the first page.
also could you give me the cost of the basic bumper and all the options you offer so i can make a decision and send you the first installment :)

The basic bumper is $265. Options are: anchor points - $50; recessed receiver hitch - $75

Orders over $500 are eligible for the payment options. Orders below $500, must be paid in full, with the shipping due upon completion

.

ok ... ? :shrug

well David while you are so active in this thread i thought i would ask about a bumper, maybe it will help other people too.

well i was wondering how mucho a bumper like this would run me. I don't need the light tabs or the winch mount as i will customize that how i want. BTW i rented this pic from JBG, it would be for an '85 fullsize not a EB http://broncograveyard.com/images/catalog/BUM2000FRONTA.JPG

swampwalker3 asked about that, and I quoted $695 ... but I may be able to bring that down a bit. Maybe down to $625, plus shipping to a business address. You're out of my freight company's shipping region, but I should be able to send it FedEx

I don't know how i missed that as i went back through and i saw the post..


BTW for a business addy, would it work to ship it to the maintence dept of my apartment building or what? and what would be a est of shippin.....thanks

49507, right? Shipping is going to be close to $135 FedEx Ground. I can't guess on the exact size, so I tried to guess high, for both weight, and size. Once it's built, I can get a more accurate shipping quote, and I'll refund any balance.

When/If you're ready, let me know anytime, and we can get things started

well actually the rents is 49057 which there might be a biz addy i can ship there, but i am up at college, that is why i was talking about if i could get it shipped to the maintence dept at my apt's. which the zip is 49307......either way i need to talk to either or to decide first if i can get it shipped..........Do ya think that would work as a biz addy, the last part i am talkin boot

Sending it to the Maint. Dept? That would be fine, so long as they're willing to accept it. I only asked about the 49057 because I didn't have one to go by, and just looked it up real quick. Shipping to either is only a 10 dollar difference, I'd just have to have the business name, to address it too, and I'll just add "Attn: Paul _____" to the address. My schedule is wide open when/if you're ready :thumbup

My schedule is wide open

That must mean mines done!!!!!



:rockon :rockon :rockon :rockon :rockon :rockon
:drinkbud :drinkbud :drinkbud :drinkbud :drinkbud

Nearly. I'm STILL waiting for those anchor mounts. if I don't get them tomorrow afternoon, I'm calling, to find out where the F they are

ok, i am goin to talk to the maintence guy here today...he shouldn't care at all. As he gets alot of my packages when i am not here.....

My schedule is wide open when/if you're ready :thumbup

Must mean mine are done too.:goodfinge

LOL, if I could afford the tubing just yet, they almost could have been. Soon tho, I'm workin on it :thumbup I'm hoping to be making another trip over there, the middle of next month, or so. Depending on when I get them done, and when the wife is taking off on her trip

O/T - BBO, would you happen to know anyone selling a V6, or V8, FWD car that runs and drives, real cheap?

No I dont,but I will keep a eye open for you though.

ok Davey, i got the guys ok.....so the shipping would be

Maintence Dept
c/o Paul I
14465 Nothland Dr Office #33
Big Rapids, Mi 49307


BTW just to add some clarity from your reply to shadowfox I assume you're wanting the winch mount, also? I've given that design alot of thought, and while it's a good enough bumper by itself, I feel it can be brought closer to the grill, so for the most part, that's going to be the major change I make. Other changes will include a full winch mounting PLATE, and a different gusseting at the bumper wings.

As i mentiod i ddin't need the winch mount as i would make up one for my custom winch setup i am doing.

Also don't worry about making the top hoop/tube, where that one has the lights, too tall as i have a 3"bl on my truck also (plus thats the reason i like that style bumper) ....Or you can try to accomodate it into the bumper, what ever works....

And last but least (:brownbag) how do ya wants yo payment

You have a PM, thanks Paul :thumbup

Here's another good lookin' one that Magnumpi posted. I'm not a fan of the brush gaurd, so how much for just the basic bumper? It's one of the first ones I've seen that doesnt look like a big bottom lip, yet it still hold a winch...Im not sure what size winch it is tho.

http://www.supermotors.org/getfile/75462/fullsize/Front_Bumper_03.JPG
http://www.supermotors.org/getfile/75463/fullsize/Front_Bumper_04.JPG
http://www.supermotors.org/getfile/75467/fullsize/Front%20Bumper%20Specs_01.JPG
http://www.supermotors.org/getfile/75468/fullsize/Front%20Bumper%20Specs_02.JPG
http://www.supermotors.org/getfile/75469/fullsize/Front%20Bumper%20Specs_03.JPG

I'll get back to you, after this weekend, with a price. I've got alot on my plate at the moment ...

............... I've seen that doesnt look like a big bottom lip, yet it still hold a winch...Im not sure what size winch it is tho.


http://www.supermotors.org/getfile/75467/fullsize/Front%20Bumper%20Specs_01.JPG
http://www.supermotors.org/getfile/75468/fullsize/Front%20Bumper%20Specs_02.JPG
http://www.supermotors.org/getfile/75469/fullsize/Front%20Bumper%20Specs_03.JPG
So WTF you tryin to say Derrick? You makin fun of me http://www.myspacetweaks.com/smilies/9/XXasshole.gif????:goodfinge :goodfinge :goodfinge :goodfinge :twak :toothless :toothless J/k D!!
Dave i was drawing up some bumpers an graph paper to scale and this is what I came up with^^^^^^^^^ A month ago. Lemme know a price on this one, please. Its the one im looking for.

Josh

How much for an Offroadtechinc.com-style (tube) one?

I still need to finalize the details, but the price is looking to be close to $850-950

Derrick, and Josh, I'll get back to you with your answers, tonight

You guys have a PM

Hey bro how much ??? is it for one of your roof racks. oneof those would look sweet on my 78 this summer.
Thanks Larry

Larry, you have a PM. Thanks for the interest :thumbup

Great work! Can't wait till I have the money to get new bumpers now. By the way, I couldn't tell if you answered this already. If I ordered a front AND rear bumper would you give a discount? Your bumpers seem pretty well priced anyhow, just curious because of my own financial imparements while I'm still in school. Hopefully a day will come when I'm not so concerned with ways to save a penny. Oh yeah I was also wondering if you make sliders and if you do what if I ordered both bumpers and a set of sliders at the same time? Would like to have them all look like they are built together and what better way than to have them all built together? :P Cheesy...whatever. Anyhow, just curious about stuff. Awesome work.

David...I know your busy....could I get a quote on something like this....at your convenience...

hehe....sorry...I can't figure out how to copy the picture. It's the 5th picture down from the beginning of this post....thanks.

Kyle

Pantsman, if you ordered all three items from me, at the same time, then yes, I can offer a discount. If you were able to leave me your Bronco, while I build these, this would make for the best fit possible. Not to say that I still couldn't, just that this way makes doubly sure. Also, keep my paypment options in mind too, when deciding what style of bumpers you're wanting


Kyle, that one sells with two different prices, depending on which layout you're wanting. No winch mount, $350. With a winch mount, $425. Plus shipping to a business address

Thanks for the interest, guys :thumbup

Hey, that'd be even better...Didn't realize you are in oregon...would much rather just leave the bronc with you and get it back with everything all on it anyhow. Maybe I can save up enough money this summer and haul down there with the moto in the back (still have to see if it'll fit I guess). Wow, that makes me want to do it even more... May have just became more of a priority than a lift and tires...maybe... Does it matter how you build it if I'm planning a suspension lift and maybe (but probably not) a small body lift later? Can't imagine suspension would matter since it'd lift the whole frame...Body lift might though from what I understand if your bumper attaches to the frame. Anyhow, I'll start saving now! :P

If you do decide on the body lift, I would like to have you install that, before you bring it down. Everything else can be done in whichever order you choose too. So, whenever you get around to it, show me the bumpers you want, and I'll give you a total price on the package deal

Shit i wish you lived close id love a double tube bumper for the front that raps around flush with the body.. I cant find them for 94 broncos anywhere on the internet.


Same here i have been trying to find a tube bumper for the rear and the only one i can find for a 1994 is $528

Can you make a skid plate for the 32 gal. gas tank on a 91 Custom? I don't want to mess with this tank anytime soon again.
Thanks, baygirl04

How much for this bumper with the tire carrier, d ring mounts, cb antenna mount, and receiver hitch? I would need for the carrier portion to be set up to hold a 35" tire with a 2005 F250 wheel on it (8 lug). What does your turn around look like right now. I have cash in full and this would look great on my 95 centurion with 2005 running gear. Let me know.
http://www.supermotors.org/getfile/265450/fullsize/11-17-05.jpg

How much for this bumper with the tire carrier, d ring mounts, cb antenna mount, and receiver hitch?
You have a PM

baygirl, I'll get back to you soon, with a price

how much would a bumper like the on ein theis pic run me??

http://www.photodump.com/direct/89StockBronc/bumperidea.jpg


its just something i wipped up in zmod a few min ago. exactly the same except maybe for some front attatchemt points for a 87-91 body style. please excuse the fact that its not perfect

how much for one like this for a 79 bronco?
weve talked before, but im just now getting it ready for bumpers. thanks

I can't recall, right off, but I was sure I gave a quote, not many posts after that one. if I haven't, I'll work up an estimate for it

Rough idea on how long turn around is on a pre-runner tube style front bumper?

Right now ... too long. At the moment, I'm booked thru early August

Right now ... too long. At the moment, I'm booked thru early August


that had to hurt!...

:beer

I don't want ot have to put anyone off, believe me. but I'm just one guy, and along with your order, I have Rob's, and another guy on the far side of Canada, in the process of paying for a large order, as well

I need to "hire" an interen... but I'm not sure if Monica knows how to run an angle grinder

Just wondering if you can do a pre-runner front and a rear bumper with tire carrier for a 1994?

tire carrier on a prerunner bumper is more difficult, but not impossible

Dave, I made a mistake:banghead I would like the prerunner for the front and a rear bumper with tire carrier and jerry can storage. Sorry for the mixup.

Ok, that's no problem, either... except for the time frame. As i've stated, I'm booked well into August, but am hoping to start making further serious progress, and get them finished by this month's end *crosses fingers*

A prerunner bumper will run you anywhere from $350 on up to about $650 - most designs are closer to $350-450 tho. Rear bumper and tire carrier, by themselves, will run $600. Options will include a receiver, anchor mounts, gas can mount, hi-lift mount

All this is to be shipped to a business address.


Thanks for the interest

but am hoping to start making further serious progress, and get them finished by this month's end *crosses fingers*




:beer :chili:

Dave,
Can you email me a way to talk with you other then email I would like both fron and rear done.

Warbird1239::notworthy

Just out of curiosity, what size Jerry can will my rear bumper hold?

David, FYI, I haven't heard back from that last PM I sent you.

well, Gerry cans are 5gl each, so I'll guess... a 5gl can?! :goodfinge

stang... PM me your question again, please. Apparently I got over excited about cleaning out some of my PM space

I found some in a hardware Store by Alan, rather cheap and all steel, so i may pick one up.

Dave,
I would like a prerunner front bar like the one you build for Big Blue
Just built a bolt-on prerunner bumper this weekend, for BadBlueOval.
What would that cost powder coated black.

:rebelflag

PM

:thumbup

Hey David! First I just want to say that after reading through this thread and seeing some of your pics, you do awesome work!!

Can you do something like this?

http://img225.imageshack.us/img225/57/bumperwt5.jpg

Of course I would need a rear bumper to match, (without the top part of course).
Shoot me an IM or email when you get a chance.

Thanks for the compliments. yes, I can definitely do that. I am quite busy at the moment, and am already taking on more work, but if you wanted to email me at diamondbackmotorsports@gmail.com with a zip code, preferrably to a business address, I can reply back with an eestimated quote

Thanks for the interest

Thanks for the compliments. yes, I can definitely do that. I am quite busy at the moment, and am already taking on more work, but if you wanted to email me at diamondbackmotorsports@gmail.com with a zip code, preferrably to a business address, I can reply back with an eestimated quote

Thanks for the interest

Email sent. Thanks David!

ok, i'm reading through this getting pretty impressed by david's work. would it be possible for his customers to post up pics of their bumpers/sliders/tire carriers/etc to give other people some ideas since many people seem to be asking for little changes?

Thanks for the compliment, Zach. I've ben hoping more would post up in the Product and Vendor review forum, but I don't want to appear like a whiney bitch :toothless

oh come on david, nothing wrong with being a whiney bitch HAHA

how booked are you now david?

About 4 front bumpers, 4 rear bumpers, at least 2 tire carriers... booked thru this month, at the very least

We need to talk sliders. :deal

Just like Marks should work fine.

Just lemme know when you got time and I'll get you the $$$$ unless you need some up front for supplies. Whatever you need lemme know.

I'll be up Portland way 9/22 to fly over to Vegas with my buddy Mike for a hockey game. Book a ticket and go with us :thumbup

9-22? Let me know when you're return flight is, and I'll try to work around that. the 22nd might be a bit too soon

oh no man i wasnt sayin have em done, i was sayin come with!

when ever you get to it. i definetely want your sliders, i just got so much other shit goin on i dont know when i'd get around to puttin em on.

You're getting a PM

Can you build one w/ a skid plate for a 96 bronco? I would like to look like the bumper in the 5th pic ( the one w/ the hood up and a warn winch mouted on it) I would also like "mine" to be able to have a winch mounted on it and for the main bar to be taller and come to more of a point--not as dramatic as a Poison Spyder Customs Trail Stinger Bumper but sort of like that---thanks Pls e-mail me your answer ckr0785@aol.com

I can, but I'm at least 5 weeks, before I can accept any new orders, so I can have time to catch up on the orders I have now. If you can wait until then, I'd be happy to take your order

Thanks for the interest

Sure I can wait but can you give me an estimate on it? Thank:drinkbud s

Yeah, sorry about that. That one will run $545, plus shipping to a business address. Keep in mind, that one sets the winch back into the grill. So, if that's not what you're wanting, changes will have to be made, affecting the price

Yea I can see what you mean about the grill-- I would rather have the bumper as close to the body as possible kind of like the on Dustin built for his Bronco ( You can see a pic of the bumper on his vendor thread Rock Sliders 80-96) I want the bronco to have a "pre-runner" look -almost- So no winch I'll just do somthing else with it--thanks :box0715:

I can make a design change, to allow the use of a winch, if you'd like. It'll only add a few bucks to the price of the bumper - maybe 10-15 bucks

Id like it to have a spot for a winch but, can you keep the bumper CLOSE to the body if you add a spot for a winch? If so then yeah--id love to mount a winch and fairfeild roller on the byumper:wacko What do you think a rear tube bumper w/ tire carrier more like spyder custom's rear trail bumper would cost?

Because I'd be building the rear stinger-tire carrier as part of the bumper, instead of an add-on that Spyder shows, the price will be $790. And that will include the license plate mount with lights. Options for that will be: recessed receiver, anchor mounts, hi-lift mount and cb antenna/aux light tabs

Okay cool, I'll keep the rear bumper in mind--but for now i'll just wait untill you have the time to build the front-about how long do you think it will be untill your caught up enough to start on teh bumper I would like>? thanks :popc1:

Good Lord, I really don't know. I'll tell ya what tho, email me diamondbackmotorsports@gmail.com on occassion, and I'll keep you updated, thru there

No problem. I'll do just that.:thumbup

David this is what I'm interested in if you can give me prices and guesstimated shipping costs.

http://img158.imageshack.us/img158/6958/mvc007sue2.jpg

I don't think you made this one but I just would like tow hooks, rear tire carrier (will it support a 35") brackets for a Hi lift jack, and a hitch reciever.

http://img182.imageshack.us/img182/1206/bum2000frontahn9.jpg

Did you ever make a front bumper like this? I am looking for somthing similar to this one.

Hey David could u build me a rear bumper for an 86 Bronco with two rectangular lights in it for backing up, two shackles, a reciver hitch, a place for license plate and a place for my CB antena all on the same bumper and how much would it be

David- I just started a new thread about this.

http://www.superford.org/getfile.php?id=111907&toggle=fullsize&f=DSCF0023.JPG
http://www.superford.org/getfile.php?id=111891&toggle=fullsize&f=DSCF0007.JPG
http://www.superford.org/getfile.php?id=111908&toggle=fullsize&f=DSCF0024.JPG
http://www.superford.org/getfile.php?id=111894&toggle=fullsize&f=DSCF0010.JPG

82' Bronco Fullsize, This front bumper, rear bumper with gas strut/swingarm tire carrier, reciever(dont care if its recessed or not-whichever is cheaper) two spots for D-rings. How much and How soon? Can pay 1/2 probably whole payment or 1st born if you accept.

Go ahead and shoot me an email at diamondbackmotorsports@gmail.com and I'll fill you in on cost and timeframe

Thanks

No Problem, Thanks

how much would a front bumper for a 89 be like of that 78 at the top???

Sorry, I don't understand what you're asking about

Daivd?

Did you ever get my PM about a front bumper for my 88?

Also intrested in sliders?

Hey David, About how much would this combo cost? Could we move the tire down 8-10 inches on the rear carrier?
Do I have to drill new mounting holes for the front or do yours bolt up to the factory location?
Thanks
(Taken from 90Beater-- hope you don't mind)
http://www.supermotors.net/getfile/431566/fullsize/front-bumper.jpg.jpg
(Taken from Ironclad-- hope you dont mind)
http://www.supermotors.net/getfile/454856/fullsize/ironclad-bumper.jpg

who do I contact to find out more info on getting a rear bumper with carrier built? Hard application to find a bumper for and those are good looking!

who do I contact to find out more info on getting a rear bumper with carrier built? Hard application to find a bumper for and those are good looking!

davids78bronco.

who do I contact to find out more info on getting a rear bumper with carrier built?

Me. After all, this IS my thread ;) But I'm going to give you a bit of forewarning... I'm slower than a turd rolling uphill, so you can't be in a hurry

Late Model Man, I'm sorry bud, I didn't see that you had asked about the bumpers. Give me til tomorrow, and I'll send you a PM

Late Model Man, I'm sorry bud, I didn't see that you had asked about the bumpers. Give me til tomorrow, and I'll send you a PM

No prob, but where's the PM? :shrug

PM sent

David, Do you build rock sliders for 78-79 broncos? if so how much do they cost? I'm about ready to order one of your rear bumpers, how far out are you right now?
let me know,
Kenny

Thought I'd run some more bumper's by ya David:
http://www.supermotors.net/getfile/462998/fullsize/000_0042.jpg
The front needs to hold a winch.
http://www.supermotors.net/getfile/462999/fullsize/000_0043.jpg
Can ya PM me? Thanks!

Thought I'd run some more bumper's by ya David:
http://www.supermotors.net/getfile/462998/fullsize/000_0042.jpg
The front needs to hold a winch.


same, please PM me

I'm wondering how well the "90Beater" front winch bumper would look on a '95 front end?

How much for a combo deal the "90Beater" front to hold Warn 9500i (see post #208) and a Big-Mike style rear (same as in post #200, w/o air) shipped to 08065? As for timeframe - I'm looking at mid-to-late summer (think August-September).

Thanks

I'll work out the estimate, later tonight. Good to read about your timeframe tho... I'm still so far behind, people are starting to get upset with me. So I won't be taking anymore orders, for at least 2 more months :brownbag

I'll work out the estimate, later tonight. Good to read about your timeframe tho... I'm still so far behind, people are starting to get upset with me. So I won't be taking anymore orders, for at least 2 more months :brownbag


Works for me - so I have time to recover from my gear install and new tires next week - my wallet will be hemoraging for a while. That way, I'll have time to save up and get the electrical system upgraded to handle the winch.

You have a PM

David I am not upset- Im next!!:chili: :chili:

After look'n through this you will definately be the guy I come to when I get some money together. Beautiful work man.

Thanks! :thumbup I seriously hope you're not in a hurry, tho... I'm still so far behind, that I've stopped joking about it

how much would a front bumper like the picture below cost but where the front license is theres a winch that comes out from behind?
http://i79.photobucket.com/albums/j125/DoggyB/Broncos/Picture049.jpg

I don't modify stock-type bumpers

hey dave i just wanted to let you know your fab skills and workmanship are awsome, i love your bumpers.... and if i can ever save up the money you are the first person i'm commin to!!! keep up the good work!!! :rockon

Thanks for the compliment. Save your pennies! And don't forget, go back to my first post in this, and read up on my available payment plans

Hi Dave, I need a rollcage like this one:

http://fullsizebronco.com/forum/showthread.php?t=42862&page=1&pp=20

I live in Buenos Aires so bringing it from USA is out of my budget, will you sell a set of drawings so I can get it done here? Thanks. Rodolfo

:brownbag :brownbag :brownbag :brownbag ...looks that David doesn´t like me.....

Sorry about this, Rodolfo, I've been even more busy than I have been. Unfortunately, I won't be able to help you out. Building a cage isn't as cut and dry as most would think. Not for me anyway


I need to take this oppportunity to thank everyone for their continued interest in having me build bumpers for them. However, I've been behind for SO long, I have neighbors constantly asking for help, and I've started looking for a house (finally!) that I'm afraid I won't be able to accept anymore orders until further notice. The poeple I've built, and have been building, bumpers for have been increasingly irritated, and rightfully so. I've asked for help, in an effort to get caught up, but no one can weld the way I want it done. I couldn't even get one guy to do my grinding for me, without gouging out my welds. My updates have fallen behind, my time has been spread thin, and I still can't find those 30 hour days

I'm sorry, folks, but I need to take care of the current orders, that I've fallen behind on, first. I'm going to build bumpers, but won't take new orders, until I get caught up. Thanks for everyone's understanding.

Sir, interested in the prerunner style in the 5th pic on the first page, I seen the price qoute, SO...

Just let me know when you are ready to take the order, and we can work something out...

Just giving this thread a bump...

Chase

David can you please contact me as soon as possible. Thanks

hye david, been thinking about doing a rear bumper this summer, so just looking a price quote of you get the time

the big-mike style bumper, but no tire carrier, just 2 clevices and a reviever hitch

how much do you think that will run me

PM me when your ready cause ill take one.

He hasn't been on in awhile, but I do know that it will be awhile as I am still waiting for mine too.

My Davids78 bumper is en route:chili: :chili:

Couple of questions: I haven't unbolted my old bumper yet, which may answer the first question. Does anyone know what diameter/length bolts to get? I don't want to be running back and forth to HD

Secondly, any strong recommedations on primer/paint combo. I want a matte black finish to match my winch bumper.
TIA

Hello, is this thing on?

1/2 x 1 1/2" Grade 8 bolts, x6. No idea on paint, I just use Krylon :shrug

cool, and thanks. Didn't want to bother you with that question. How's everyone doing?

new thread in the Gen Discussion ;)

My Davids78 bumper is en route:chili: :chili:

Couple of questions: I haven't unbolted my old bumper yet, which may answer the first question. Does anyone know what diameter/length bolts to get? I don't want to be running back and forth to HD

Secondly, any strong recommedations on primer/paint combo. I want a matte black finish to match my winch bumper.
TIA

I have this Zero Rust on my bumper, its pretty good, only scratchs with Metal on Metal it seems like, I would love to get powder coating, but the price for something that big, will just have to wait

I decided to build my own front bumper -- but at the suggestion of others--I am thinking about letting someone else make my rear bumper (or buy and alter it form poison spyder) I was wanting to double check---Is the price still the same as below + What is the cost of the hi-jack carrier and 2 anchor mounts In addition (what would the bumper that you would build look like)?-- and what would the cost be for just the carrier--I would mount it to square (rectangular) tubing-- I would still want the lisence plate as syder has it and I would also want the hi-jack mount


Because I'd be building the rear stinger-tire carrier as part of the bumper, instead of an add-on that Spyder shows, the price will be $790. And that will include the license plate mount with lights. Options for that will be: recessed receiver, anchor mounts, hi-lift mount and cb antenna/aux light tabs

EDIT: SRY I didn't read page 12... let me know when your ready to start back up.. But if you have time soon just PM me or post here or e-mail ckr0785@aol.com which ever thanks

Thought I'd run some more bumper's by ya David:
http://www.supermotors.net/getfile/462998/fullsize/000_0042.jpg
The front needs to hold a winch.



can i get a price 4 this 1 2?

Hi David

This is Paul Boudreault

I joined ot try to get a hold of you.

Am looking for an update on my fornt an rear bumper with the features i ordered, and rock slider with powder coating on all (Gloss black or as close as possible) order for my 1979 bronco, (pre paid).

Havent heard from you in while and this order as you know has been with for quite a while.

Please PM me, email me telephone me, throw a carrier pigoen out your window to me, hire punks to spray paint the message on my house, etc. something, so i can make finail delievery arrangements or at least get a shipping or completion date.

Pictures of what you have done and drawing of these bumpers as they are going to be made with the ordered features would be nice too.

I have heard you have delays, but before i get flamed by people i have been waiting a very lonnnggg time for these. ( not going into it here it will just cause grief and that is not waht i want i just want my order asap).

I need some feedback here.

Thanks for your cooperation

Mr. Paul Boudreault
Porject bronco Member

Hi David,
If you can give me the same treatment I would appreciate it. I have sent you several emails w/no response.

I guess the only positive thing here is that in a few months we can have an anniversary. :toothless

Please PM, email, rock w/paper wrapped around it- whatever.

Thanks
Thomas

David,
I have sent you several emails, posted several requests on here. I have also been in contact with several other people, who have received responses from you, while I have not.

I gave you 1/2 security deposit on 12/15/06. I also gave you several other payments, because it seemed you were short on money, and I liked your product- for a total of 1000.00.

You have repeatedly blown off getting back to me on deadlines that YOU HAVE SET. In other words, for people reading this, because I am sure someone wants to give me their opinion, David has told me he was several welds away from finishing three or four times, and that he would let me know in a week or two. These deadlines have come and gone, and no action, no phone calls, no emails, no nothing sent to me to let me know what is going on unless I INITIATED IT.

I may not be that quick on the uptake, but I would say without a doubt, and by reading other emails, that you have made other bumpers first and blown me off, and now due to circumstances beyond your control, may not have the materials, and or the money to fill my order.

You have said repeatedly that you are almost done. My request for pictures has gone unanswered, as if I never even asked for it. The one picture I did get was a generic picture of the latching mechanism you would be using. Great, super, how about a picture of the product you are supposedly making for your client.

And that is what is comes down to. I am a client of yours, that needs to speak to the management, the complaint dept., etc. You have not fulfilled any of the obligations you said you would.

To those of you who are reading this, I am not the only one. So if you are thinking about also becoming one of david's clients, you may want to re-think it, no matter how sweet it looks in the picture, when you don't recieve it, it is not very sweet at all.

You would be better off giving your money to someone you don't know to invest it, no matter how hare-brained the scheme, because you would get feedback on it, negative or positive, it would still be feedback.

DAVID, I need a reply, an email, an explanation, a phone call. I need something to re-assure me that I have not been taken to the cleaners- or hustled. I need to know when I am recieving a product, or if I am getting my money back, or I am going to do something about it. I am done screwing around with this.

-Thomas

please see this thread for any information or possible updates (http://fullsizebronco.com/forum/showthread.php?t=102842), Davids vendor status has been temporarily suspended until he can catch up with his orders and better communicate with his customers.

Please be advised that although we at FSB will do what we can to help you, David and his business is in no way affiliated with FSB, please direct your communication to David directly either via PM, email or other contact information you may have for him but dont hesitate to contact me with any questions, I'll try to do what I can, however, that is extremely limited at this point.

I feel confident that David will come through for those who he owes either products or possible refunds, hopefully he will be online soon or in communication with those customers who are waiting.

Thank you for your understanding,

Joe