I've had a lot of people unsure of the length to order, so I added a new "kit" to my site:

http://fordfuelinjection.com/images/alt-cable2.jpg
5ft of 2 gauge heavy duty cable rated -60°F to 220°F.
Mega-Fuse holder
2 - 175Amp Mega-Fuses
Red Protective Boot for Alternator connection
4 lugs (3/8″ for Battery, 1/4″ for Alternator, 5/16″ for Mega-Fuse)
Red Adhesive Lined Heat Shrink
Solder Pellets
Must have a Propane torch for assembly

$40 + S&H
http://fordfuelinjection.com/?p=67

Nice. Wish I'd bought that.

Do you sell the components? I'd like a lug for the megafuse block and some heatshrink, so I can shorten my too long charge cable.

Added a Replacment Lug Kit to the wed site

5/16" lug for Mega-Fuse
2" Red Adhesive Lined Heat Shrink
1 Solder Pellet
Must have a Propane torch for assembly

$4 + S&H
http://fordfuelinjection.com/?p=67

Excellent.

(I have to say, that's some impressive response time to a customer-expressed desire.)

Thanx Ryan I'll be orderin that real quick! I was unsure as the length myself and it always seemed to get pushed back cause of it. Way to go man :thumbup


Joe

Right on! I'll be ordering one, for my 3G, sometime in the near future

(thread hijack) can you get just the boots? and in different colors? (end hijack)

What do you need the boots for?
I typically only use Red boots because ground isn't dangerous.

What do you need the boots for?
I typically only use Red boots because ground isn't dangerous.
would like to replace the boots on my winch were the cables bolt on...colors are red,black,and yellow.

I can get Red and Black, I've never looked for yellow.
I don't want to buy a bulk pack just to sell you one boot.
Sorry

I can get Red and Black, I've never looked for yellow.
I don't want to buy a bulk pack just to sell you one boot.
Sorry
no problem..just seeing if you carried them...:thumbup

Ryan, i am gonna be doing a 3g install on my uncles 390 using a 92 taurus 130amp. would the wiring harness listed first on your site get the job done and of course i would need to order the fuse block/cable package as well.

question....what are you using for connections to the battery itself? like battery terminals? I need to get this kit from you but would also like to order everything to redo my starting/charging system for 2 batterys at the same time.

you can pm me some info if you dont want to clog up this thread. I want to do this soon and pretty much planned to get it from you so let me know

you want some solder on lugs for top post batteries?

I would like to do everything and make provisions for duel batterys. I would need everything to do that from you.

yeah i perfer the solder terminals for the battery. those generic crimp junk terminals sucks nuts

I just added battery cable parts to my site: http://fordfuelinjection.com/?p=87
Not all of it will be in stock untill next week

TTT

. If you have those let me know. i already have the batterys, just need the crap to hook it up in the truck. can I get bulk cable in red and black from you too?

opps didnt see your last post.

anyhow Im going to measure what I need and place an order within the next day or so just to have it done.

it can ship whenever you get them instock.

Ryan, i am gonna be doing a 3g install on my uncles 390 using a 92 taurus 130amp. would the wiring harness listed first on your site get the job done and of course i would need to order the fuse block/cable package as well.


ttt, you can pm me if you prefer. thanks

Ryan, i am gonna be doing a 3g install on my uncles 390 using a 92 taurus 130amp. would the wiring harness listed first on your site get the job done and of course i would need to order the fuse block/cable package as well.
3G's all hook up the same, only change between vehicles is how much old junk there is to remove.
You can get rid of all the old wiring and regulator.

Thanks Ryan, i will get a harness ordered then.

Must have a Propane torch for assembly

So what kind of torch, like the small ones you can buy at Home Depot/Lowes for soldering copper pipe?

http://www.homedepot.com/cmc_upload/HDUS/EN_US/asset/images/eplus/070042196245_4.jpg

This is the style I use......
http://www.machinemart.co.uk/images/products/mid/MM010117080.jpg

I use a larger Bernzomatic for these cables, but I guess the smaller one Dustin has would work.

I use a larger Bernzomatic for these cables, but I guess the smaller one Dustin has would work.

Ive done them with it, just takes a little longer to heat up. I solder alot of stuff with my little torch, even have a soder tip for it

So how do you solder those? Just heat up the lug with the solder pellet in it, then put the wire in while the solder is liquid?

I've never soldered those battery lugs before, just the smaller gauge wires.

that's it, not too hard a task

Cool, I'll have to order some parts next payday.

:thumbup

OK Ryan,
I just ordered...
160 amp side mount alt
200 amp rectifier
2 1/4 serp pully
and the
charge cable kit.
It is being shipped to Christopher Harper in San Diego CA.
Is there any way you or your associates put 225A fuses in the kit instead of 175?
Chris

Yes I can send you 225A fuses
Just keep the cable as short as possible!

Thanks Ryan! Short cable, got it!:thumbup
I will do a short write up when i install it.

just ordered, was gonna look for this stuff locally but I would rather support a fellow Bronco owner:thumbup

I ordered the longest prefab style and was planning to just cut it down if it was too long. Any problem with that?

you need the correct lugs or it will ruin the quality of the product.