Ford Bronco Forum - Reply to Topic
Thread: Which radius arm bracket is strongest? Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
   

Register Now



In order to be able to post messages on the Ford Bronco Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself. DO NOT USE Gmail.com accounts. If you only have a Gmail.com email please contact the administrator here

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-09-2013 11:50 PM
Kingfish999
Quote:
Originally Posted by Alvin in AZ View Post
I got bigger better bolts on my stock radius arm bracket than you got on that
longass drop radius arm bracket. xD

...9/16" fine thread grade-8 bolts with pinched top nuts and ->NO<- washers
from McMaster-Carr. |-p

Alvin in AZ
thats not mine, i found that pic on google. i have extended radius arms with stock brackets. 1 bracket is 1/2" bolts and the other is 7/16" all grade 8 fine thread of course. 9/16" is way overkill IMO
02-09-2013 01:10 PM
Steve83
Quote:
Originally Posted by JAYNESS the Great View Post
I HATE lifting it by the brackets, but with the way these particular lift arms were designed and the extended radius arms in the way...
There's nothing wrong with lifting by the RA brackets, and the stock RAs are the alternate lift points. IDK if those aftermarket ones can handle it, though...
02-09-2013 11:11 AM
Alvin in AZ
Quote:
Originally Posted by Kingfish999 View Post
dropped radius arm brackets used for lift kits over 4" such as this
I got bigger better bolts on my stock radius arm bracket than you got on that
longass drop radius arm bracket. xD

...9/16" fine thread grade-8 bolts with pinched top nuts and ->NO<- washers
from McMaster-Carr. |-p

Alvin in AZ
02-09-2013 07:27 AM
JAYNESS the Great That's the side post lift I was using. The truck is about 5ft off the ground in these pics. I HATE lifting it by the brackets, but with the way these particular lift arms were designed and the extended radius arms in the way, it was my only option.
02-09-2013 04:05 AM
Kingfish999 whats welded to the bottom? i wish i still had the brackets form my friends lift kit. they were in great condition and i woulda gave them to ya free.
02-08-2013 11:13 PM
JAYNESS the Great I had some time after working on the exhaust last weekend and spent some time on the radius arm bushings. I was surprised to find that the inside of the bushings looked pretty good. (the outsides were crumbling) I'm thinking that the brackets look ok, I just need to clean them up and POR-15 them.

Here's some pics:

Pass side 1


Pass side 2


Driver side 1


Driver side 2


I did go ahead and replace the rear half of the bushing since it was taken apart anyway. I'll get the front half when I have time to remove the bracket.
01-18-2013 10:36 PM
Kingfish999 dropped radius arm brackets used for lift kits over 4" such as this
01-18-2013 09:22 PM
JAYNESS the Great
Quote:
Originally Posted by Steve83 View Post
... (EXCEPT lifted ones which are effectively weaker)...
What do you mean "lifted ones"?
01-18-2013 09:07 PM
Steve83 Rust doesn't cause the factory coating to flake; the flaky coating traps water & salt, causing rust. There's no point even guessing until you know what yours look like, and you can do that quickly by simply removing the big nut, rear washer, & rear bushing. That's all it takes to inspect the bracket for wear, then you can put it all back until you're ready to fix it. If it's OK, reuse it. If it's trash, buy a replacement - there is no "strongest"; they're all the same (EXCEPT lifted ones which are effectively weaker). If you don't know, take some GOOD pics, and I'm sure plenty of opinions will be offered!
01-18-2013 06:32 PM
Kingfish999 there all gonig to be bout the same strength. i cant say i ever heard of someone breaking them from wheeling. only that they rusted out. also if the bushing is completly worn out and the arm is rubbnig the lip of the hole, it will wear them out and you do need to replace them. jsut get a cheap set of them that are still in good condition.
01-18-2013 05:32 PM
JAYNESS the Great
Which radius arm bracket is strongest?

I'm going to replace my radius arm bushings soon and I'm contemplating replacing the brackets since I'll be taking them off anyway. I'm not sure if the radius arm holes in the bracket are ok or not (there's some bushing left), but the bracket is rusted enough that the factory coating is flaking off. The ones from Ford are pretty expensive, are the aftermarket ones equivalent or thinner/weaker?

Oh yeah, I have ProComp extended radius arms so the brackets have already been moved using bolts instead of rivets.

Thanks.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome