Your Junkyard Finds! - Page 21 - Ford Bronco Forum
 328Likes
Reply
 
LinkBack Thread Tools Display Modes
post #401 of 471 (permalink) Old 09-14-2019, 12:46 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Part Two:

By the time I got to the camper, I'd already been there for about an hour, and didn't really feel like trying to get the York.

On my tour yesterday, I saw a bronco transmission/transfer case in the engine pile. I figured I'd get the flange output in case I ever wanted to convert the F150 into a Bronco one. I also pulled the case apart to get the entire output shaft that goes with it, but didn't have any snap ring pliers to get it off. So I stashed it all, plus the one half of the driveshaft in an old van (hopefully to separate and get later).

Then I spent about 30 minutes standing around while some random guy talked my ear off about all the old ford trucks nearby, and how any of them would be nice to have, even though he's a chevy guy.

On the way out, I spotted some broken transfer case that I couldn't immediately recognize that had a double cardan joint on the front driveshaft. Since it was broken, I couldn't keep the shaft from spinning to get the yolk unbolted, so I took the whole thing to the front. $10. Not bad considering I don't know what its out of or if it will work on my transfer case.

It's Hard To Beat A Good Sandwich
67galax is online now  
Sponsored Links
Advertisement
 
post #402 of 471 (permalink) Old 09-14-2019, 01:12 PM
Addicted to Junk
 
BigBlue 94's Avatar
 
Join Date: May 2006
Location: Hoyt, Kansas
Posts: 9,961
Bronco Info: 85 Bronco, 309ci I6 w/4bbl, np435, 4" lift, 37" Irok NDs, 4.56 w/ Detroit Locker and tru trac
iTrader: (7)
Garage
Not sure if you're aware, but those Onan generators are built by Cummins. They are about the best generators you can get. I would ask them what they want for it, before touching it. I'd gladly pay 200 bucks to pull that puppy if it works.

Double cardon front driveshafts usually only come on solid front axle trucks. Was it an iron case or non-ferrous?



309ci inline 6, 9.75:1 CR, Big Valves, ROLLER ROCKERS, Clifford intake and headers, Schneider 140H cam, DUI HEI ignition, 450 QFT 4bbl carb, Saginaw swap, FlowKooler water pump, Steel timing gears, 2.5in y-pipe into a single 3in cat and borla muffler.
BigBlue 94 is offline  
post #403 of 471 (permalink) Old 09-14-2019, 01:30 PM
Addicted to Junk
 
BigBlue 94's Avatar
 
Join Date: May 2006
Location: Hoyt, Kansas
Posts: 9,961
Bronco Info: 85 Bronco, 309ci I6 w/4bbl, np435, 4" lift, 37" Irok NDs, 4.56 w/ Detroit Locker and tru trac
iTrader: (7)
Garage
Looks to be an Onan 3.0RV Genset, which from my little research, is a great little unit and rebuildable.
67galax likes this.



309ci inline 6, 9.75:1 CR, Big Valves, ROLLER ROCKERS, Clifford intake and headers, Schneider 140H cam, DUI HEI ignition, 450 QFT 4bbl carb, Saginaw swap, FlowKooler water pump, Steel timing gears, 2.5in y-pipe into a single 3in cat and borla muffler.
BigBlue 94 is offline  
post #404 of 471 (permalink) Old 09-14-2019, 01:43 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Quote:
Originally Posted by BigBlue 94 View Post

Double cardon front driveshafts usually only come on solid front axle trucks. Was it an iron case or non-ferrous?
Here are some pics. Quick Google search makes me think its a Jeep NP231









BigBlue 94 likes this.

It's Hard To Beat A Good Sandwich
67galax is online now  
post #405 of 471 (permalink) Old 09-14-2019, 01:48 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Quote:
Originally Posted by BigBlue 94 View Post
Looks to be an Onan 3.0RV Genset, which from my little research, is a great little unit and rebuildable.
Do those output 110 or 220? I could really use a propane powered 220.

It's Hard To Beat A Good Sandwich
67galax is online now  
post #406 of 471 (permalink) Old 09-14-2019, 02:09 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Well, after a few hits with the old impact, I got the yoke off the jeep transfer case. Since I also pulled a rear flange off a 95 bronco, I compared the two. The splines on the jeep front output are larger than the bronco rear, meaning I probably won't be able to use it on my bronco transfer case. I read somewhere earlier that you could use a bronco rear flange on the front to get a double cardan on the front.

Quote:
Originally Posted by Kingfish999 View Post
if your swapping to one you have 3 options. you can find the rare front output yoke from a F350 transfer case that had them, then you can use a 1350 driveshaft for best strength. or you can find a rear output yoke from a 87-89 Bronco and swap it on the front, it will use a 1330 driveshaft which is good still. last option is finding a rear output flange from a 90-96 bronco and swap it on but the splines will have abit of slop when swapped on the front because they are very slightly different. this was the method i choose and haven't had any issues yet and im using a 1350 driveshaft but can also use 1330 if you want to be cheaper

It's Hard To Beat A Good Sandwich
67galax is online now  
post #407 of 471 (permalink) Old 09-14-2019, 02:36 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Quote:
Originally Posted by Handy_andy_cv64 View Post
They don't need pressure to blow, just volume.
I used one of those rubber cone tipped blow guns from my compressed air tank and shot a few bursts through those horns. Nice and loud, but I'm not sure if both or only one is working. Sounds like one of those emergency boat horns that comes with its own canned air supply.

It's Hard To Beat A Good Sandwich
67galax is online now  
post #408 of 471 (permalink) Old 09-14-2019, 04:25 PM
Addicted to Junk
 
BigBlue 94's Avatar
 
Join Date: May 2006
Location: Hoyt, Kansas
Posts: 9,961
Bronco Info: 85 Bronco, 309ci I6 w/4bbl, np435, 4" lift, 37" Irok NDs, 4.56 w/ Detroit Locker and tru trac
iTrader: (7)
Garage
Quote:
Originally Posted by 67galax View Post
Do those output 110 or 220? I could really use a propane powered 220.
You'll have to find the model number to be sure, but it might be only 120v. Seems to be a 3000w generator. Not sure if you could convert to 220/240v. Appears to be a number of YouTube videos about em.

Here's an operating manual for a similar if not exact model

https://www.manualslib.com/manual/89...et.html#manual
67galax likes this.



309ci inline 6, 9.75:1 CR, Big Valves, ROLLER ROCKERS, Clifford intake and headers, Schneider 140H cam, DUI HEI ignition, 450 QFT 4bbl carb, Saginaw swap, FlowKooler water pump, Steel timing gears, 2.5in y-pipe into a single 3in cat and borla muffler.
BigBlue 94 is offline  
post #409 of 471 (permalink) Old 09-14-2019, 04:35 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Quote:
Originally Posted by BigBlue 94 View Post
You'll have to find the model number to be sure, but it might be only 120v. Seems to be a 3000w generator. Not sure if you could convert to 220/240v. Appears to be a number of YouTube videos about em.
Even if its only 120v, its still a generator with a fuel supply that doesn't go bad over time. It will still run my freezer, just not my well pump.
BigBlue 94 likes this.

It's Hard To Beat A Good Sandwich
67galax is online now  
post #410 of 471 (permalink) Old 09-14-2019, 09:00 PM
House of Windsor 4ever!
 
Handy_andy_cv64's Avatar
 
Join Date: Jul 2006
Location: Everett, WA
Posts: 10,442
Bronco Info: 79 Ranchero GT "Babe the Blue Ox"/97 Eddie Bauer Exploder 5.0 AWD
iTrader: (2)
Garage
Oh, yeah, that ugly SOB. I call those RVs the "Speculum." You can get one of those air movers for the horns off Amazon, a complete install kit. If the hose is Y'd before their attachment to the horns, you can pull the Y off, and attach the long hose to each one, test them separately. Even with one's breath pressure, they are loud!
BigBlue 94 likes this.

_____________________________________________

LINK??? Link yourself down to Walmart!
Handy_andy_cv64 is offline  
post #411 of 471 (permalink) Old 09-15-2019, 08:54 AM
FSM Lifetime
 
oshere's Avatar
 
Join Date: Sep 2015
Location: north Syracuse NY
Posts: 179
Bronco Info: '83 Full size Bronco Custom 302 Auto , under reiteration but starts and runs
iTrader: (0)
Garage
Junkyard fine for anyone in Maryland Chesapeake Bay Area. My brother-in-law sent me these pictures see if there's anything I wanted and I thought I'd share. If anyone's interested I can ask him the exact location I think it's the junkyard in Harve De Grace Maryland. I'm hoping he can go back pull the seats look to see if there's a steering wheel and the emblems and that rear deflector but the front fenders look good for anyone needs front fenders.

Sent from my SM-N920V using Tapatalk
BigBlue 94 likes this.

Honey badgers have been known to
eat porcupines,
eat poisonous snakes,
raid beehives,
kidnap baby cheetahs,
take food from hungry lions.

Honey Badger Donít Care.
oshere is offline  
post #412 of 471 (permalink) Old 09-15-2019, 11:29 AM
Addicted to Junk
 
BigBlue 94's Avatar
 
Join Date: May 2006
Location: Hoyt, Kansas
Posts: 9,961
Bronco Info: 85 Bronco, 309ci I6 w/4bbl, np435, 4" lift, 37" Irok NDs, 4.56 w/ Detroit Locker and tru trac
iTrader: (7)
Garage
@BroncMom needs those window switch bezels...



I had forgotten about potentially the BIGGEST find of my last trip. It was raining, so I had my phone packed away.

It was a 78-91 style of center console, with FACTORY DEEP cup holders. They were molded in, just like normal, but about 2" deep! It was in an 80s supercab pickup. I've got a tuffy so I didnt need it. And I cant be hoarding too many parts at the moment... nowhere to put em. I still have that D60 in the back of my van.
67galax likes this.



309ci inline 6, 9.75:1 CR, Big Valves, ROLLER ROCKERS, Clifford intake and headers, Schneider 140H cam, DUI HEI ignition, 450 QFT 4bbl carb, Saginaw swap, FlowKooler water pump, Steel timing gears, 2.5in y-pipe into a single 3in cat and borla muffler.
BigBlue 94 is offline  
post #413 of 471 (permalink) Old 09-15-2019, 12:12 PM
Fullsize Member
 
67galax's Avatar
 
Join Date: Nov 2005
Location: Southeast Iowa
Posts: 1,054
Bronco Info: 1996 XLT currently motorless, ZF5 trans, sitting on old 33's
iTrader: (0)
Garage
Quote:
Originally Posted by BigBlue 94 View Post
And I cant be hoarding too many parts at the moment... nowhere to put em. I still have that D60 in the back of my van.
I know exactly what you mean. I have so many parts for projects that I really want to, but may never, happen. Then the problem becomes, they're so large that you can only hope to sell them locally due to shipping. I just hate the idea of desirable parts being lost forever.

My wife is constantly on me about getting rid of my 'crap' in the garage.

I can't even work on my Comet because I have a D60, a Sterling, and a D44 solid and some TTB beams sitting behind it. I'm gridlocked in my own garage.
BigBlue 94 and GetBent4x4 like this.

It's Hard To Beat A Good Sandwich
67galax is online now  
post #414 of 471 (permalink) Old 09-15-2019, 12:21 PM
Registered User
 
biggum's Avatar
 
Join Date: Sep 2016
Location: Maine
Posts: 1,526
Bronco Info: 86 XLT 351 HO, Holley 650, 3" Exhaust, 6L Up, 265/75R16 Dirt Commanders, & 85 302 EFI, AOD, 6L Up
iTrader: (0)
Garage
Pull those window switches! Someoneís sure to want those!!


Sent from my iPhone using Tapatalk Pro

When you have to shoot, shoot - don't talk.
https://binged.it/2LnJaeA
biggum is online now  
post #415 of 471 (permalink) Old 09-16-2019, 06:08 PM
House of Windsor 4ever!
 
Handy_andy_cv64's Avatar
 
Join Date: Jul 2006
Location: Everett, WA
Posts: 10,442
Bronco Info: 79 Ranchero GT "Babe the Blue Ox"/97 Eddie Bauer Exploder 5.0 AWD
iTrader: (2)
Garage
Who the Heck was driving that Bronco? Johnny Blaze?

I think it also has power locks, grab those, and the metal interior door handles, much better than the '87-and-up plastic ones.
BigBlue 94 likes this.

_____________________________________________

LINK??? Link yourself down to Walmart!
Handy_andy_cv64 is offline  
post #416 of 471 (permalink) Old 09-16-2019, 08:04 PM
Addicted to Junk
 
BigBlue 94's Avatar
 
Join Date: May 2006
Location: Hoyt, Kansas
Posts: 9,961
Bronco Info: 85 Bronco, 309ci I6 w/4bbl, np435, 4" lift, 37" Irok NDs, 4.56 w/ Detroit Locker and tru trac
iTrader: (7)
Garage
Quote:
Originally Posted by biggum View Post
Pull those window switches! Someoneís sure to want those!!


Sent from my iPhone using Tapatalk Pro
Quote:
Originally Posted by Handy_andy_cv64 View Post
Who the Heck was driving that Bronco? Johnny Blaze?

I think it also has power locks, grab those, and the metal interior door handles, much better than the '87-and-up plastic ones.
As I said, @BroncMom needs those switch bezels! Lol

Johnny Blaze, as in Ghostrider? Or Method Man?

Theres a 92+ 4.9L/7.5L air inlet snorkel in one pic lol...



309ci inline 6, 9.75:1 CR, Big Valves, ROLLER ROCKERS, Clifford intake and headers, Schneider 140H cam, DUI HEI ignition, 450 QFT 4bbl carb, Saginaw swap, FlowKooler water pump, Steel timing gears, 2.5in y-pipe into a single 3in cat and borla muffler.
BigBlue 94 is offline  
post #417 of 471 (permalink) Old 09-17-2019, 03:13 PM
Foolsize Member
 
92BroncoXLT's Avatar
 
Join Date: May 2009
Location: Middle Georgia
Posts: 1,509
Bronco Info: They multiply when I'm not looking.
iTrader: (0)
So recently Iíve been looking to swap from my factory 3:08ís to 3:55ís to help my old 300 turn my 33ís a little easier. So cruising around carpart.com I see a 94 F150 at a yard here in town (the kind that wonít let you wander around). As Iím scrolling through the pictures and notice the axle code on the door tag is ďH92Ē designating 3:55ís with front and rear LSDís. I immediately called them and asked if the axles were still under it and they said the rear is gone but we still have the front. I told them to pull it and Iíd be by today to pick it up.

I got there and figured out that when they pulled it, they didnít want to do much disassembly. So Iím now the proud owner of the front 1/4 of an F150 frame
Attached Thumbnails
Click image for larger version

Name:	047BE13F-1A51-4861-9BF5-29DC2D94A579.jpg
Views:	10
Size:	507.3 KB
ID:	142584  


Dylan

1992 XLT 300/M5OD
1978 Custom 351M/C6
2014 Mustang GT
1991 BMW 525i
Ford Parts manager, members needing help researching or locating Ford OEM parts send me a PM!
92BroncoXLT is offline  
post #418 of 471 (permalink) Old 09-18-2019, 09:56 AM
Addicted to Junk
 
BigBlue 94's Avatar
 
Join Date: May 2006
Location: Hoyt, Kansas
Posts: 9,961
Bronco Info: 85 Bronco, 309ci I6 w/4bbl, np435, 4" lift, 37" Irok NDs, 4.56 w/ Detroit Locker and tru trac
iTrader: (7)
Garage
Nice score! That's like a 1 in 50,000 option (no actual clue)

Now if it was a 4.10... itd be like finding a unicorn!



309ci inline 6, 9.75:1 CR, Big Valves, ROLLER ROCKERS, Clifford intake and headers, Schneider 140H cam, DUI HEI ignition, 450 QFT 4bbl carb, Saginaw swap, FlowKooler water pump, Steel timing gears, 2.5in y-pipe into a single 3in cat and borla muffler.
BigBlue 94 is offline  
post #419 of 471 (permalink) Old 09-18-2019, 10:55 AM
Foolsize Member
 
92BroncoXLT's Avatar
 
Join Date: May 2009
Location: Middle Georgia
Posts: 1,509
Bronco Info: They multiply when I'm not looking.
iTrader: (0)
Quote:
Originally Posted by BigBlue 94 View Post
Nice score! That's like a 1 in 50,000 option (no actual clue)

Now if it was a 4.10... itd be like finding a unicorn!
I originally wanted to hold out and find a set of 4.10's, but having the torque of the 300 and being on pavement 90% of the time means 3.55's will do just fine. Now I just need to grab a rear axle to match and i'll be set (thankfully a truck with an H9 axle code is pretty common)

EDIT: Forgot to mention that whole frame/axle section only cost me 200$!
BigBlue 94 likes this.

Dylan

1992 XLT 300/M5OD
1978 Custom 351M/C6
2014 Mustang GT
1991 BMW 525i
Ford Parts manager, members needing help researching or locating Ford OEM parts send me a PM!
92BroncoXLT is offline  
post #420 of 471 (permalink) Old 09-18-2019, 11:32 AM
FSM Lifetime
 
dash_cam's Avatar
 
Join Date: Nov 2014
Location: dallas tx
Posts: 3,135
Bronco Info: 1996 EB, 351w, stock-ish. 1981 custom 351m, long gone.
iTrader: (4)
Garage
Quote:
Originally Posted by 92BroncoXLT View Post
I originally wanted to hold out and find a set of 4.10's, but having the torque of the 300 and being on pavement 90% of the time means 3.55's will do just fine. Now I just need to grab a rear axle to match and i'll be set (thankfully a truck with an H9 axle code is pretty common)

EDIT: Forgot to mention that whole frame/axle section only cost me 200$!
that has a lot of extra usable parts that you could sell or hoard, too.
dash_cam is offline  
Sponsored Links
Advertisement
 
Reply

  Ford Bronco Forum > Other Forums > General Discussion/ Bronco and Wheeling related.

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Bronco Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself. DO NOT USE Gmail.com accounts. If you only have a Gmail.com email please contact the administrator here

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome