Ford Bronco Forum - Reply to Topic
Thread: What did you do to your bronco today? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Ford Bronco Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself. DO NOT USE accounts. If you only have a email please contact the administrator here

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
Yesterday 09:14 PM
Ford 4x4 Put in a new coil, cap, and rotor. New wires and plugs to come.
Yesterday 09:03 PM
Kingfish999 Spent most of the day diagnosing my misfire issue. Found out it was the fuel injector on cylinder 1 not firing. Eventually found the PCM was burnt. Swapped a damaged one in for now. Seems good. Rain killing most of the day. Did replace the coil with a Holley Sniper EFI coil which is basically a ordinary TFI coil but with a cool remote mount bracket which I need due to my aftermarket mustang style intake manifold. Old coil was an Accel Ultracoil which was also remote mount
Yesterday 04:23 PM
Frank Lanzisera Front and rear plastics done
Yesterday 01:27 PM
Want2BS8ed Cleaned her up inside and out and moved all my junk back in after the engine swap.

Nice to have the truck back.
Yesterday 12:50 PM
BroncMom Pulled the cargo panel mounting bars and the rear speaker mounting brackets in prep for rust removal & monstaliner application this week. Hubby's bringing home an angle grinder for me to play with
Yesterday 12:26 PM
biggum Tried out my Holley mods on some steep stuff final. Works great!

Sent from my iPhone using Tapatalk Pro
Yesterday 08:28 AM
MS88Bronc Went to play in the rocks and dirt yesterday. Will be posting more pics and vids in the FOTM thread soon - need to figure out how to edit some video.
09-14-2019 11:20 PM
Kingfish999 replaced the harmonic balancer on the 96 today with one rebuilt by DamperDudes. now i can detect misfires again. had another rebuilt for the 88 since its also using 96 EFI also and will probably do it tomarrow. now that it shows misfire data, it shows cylidner 1 is where my misfires are coming from so i replaced its spark plug hoping for a simple fix but was not the cause. then suddenly my ignition coil decided to die while im at the auto parts store (luckily for me) so i have a temporary one in for now. going to try a leakdown test tomarrow and check the fuel injector.

09-14-2019 07:23 PM
Frank Lanzisera Took the front bumper trim off to coat with the Eastwood plastic resurfacer. Clips came out in 10 minutes. Finish it tomorrow.
09-14-2019 05:54 PM
nra1ifer Added a Tekonsha T-One trailer connector to our 1981 Bronco. Piece of cake to install other than some existing brittle wiring near the connectors that are separated for this install....
09-14-2019 05:43 PM
67galax I mentioned it in my build thread, but I started the 4-bolt steering swap. Ordered the AN fittings and hose today.
09-14-2019 05:18 PM
Frank Lanzisera
Originally Posted by Want2BS8ed View Post
That’s impressive looking Frank. What paint are you using on the air dam?
Eastwood plastic resurfacer. Used their xylene paint prep first. Matte black.
09-14-2019 03:59 PM
Originally Posted by Frank Lanzisera View Post
Half the front spoiler done half not

Thatís impressive looking Frank. What paint are you using on the air dam?
09-14-2019 03:49 PM
Frank Lanzisera Half the front spoiler done half not
09-14-2019 01:26 PM
Frank Lanzisera Prepping and finishing flat black exterior parts
09-14-2019 12:48 AM
Originally Posted by BroncMom View Post
Wish I could drive to LMC truck.
Don't we all?
09-13-2019 09:19 PM
Originally Posted by BroncMom View Post
Yay for new tailgate cables
Hard to beat a new set of cables!

I ordered a new passenger side window motor for the 93 tonight. It was getting slower and slower, then died. Luckily with the window up!
09-13-2019 06:38 PM
66WarPony Flowtech Headers and 351 + computer successfully swapped over - BUT the extra standoff of the EGR Tube from the PS Header required grinding a 1/4" off the back of the Alternator/Smog Pump Bracket. The only thing left to do is drop the exhaust, grind down and redo one of the crappy welds on the Y-Pipe to Cat because I can't get my stinger in there. Short write-up coming soon...

Sent from my XP8800 using Tapatalk
09-13-2019 06:20 PM
Originally Posted by BroncMom View Post
Hey @MS88Bronc they weren't terrible thru LMC. $10 per cable, screw & spacers $2 a set x4 (if u want all new hardware) and $4 each for the cable springs, which would appear I can't use on mine, so if u can use em I'll send em to ya.

Thanks! Itís not a huge priority at the moment, but they are cracking and such. Iíll get around to it one of these days!
09-13-2019 05:50 PM
BroncMom Got everything pulled in the cargo area so I can pull the carpet and Simonize the 30+ years of Arkansas out of the back of my rig
This thread has more than 20 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome