Ford Bronco Forum

Ford Bronco Forum (https://www.fullsizebronco.com/forum/)
-   78 - 96 Build Forum....Builds only (https://www.fullsizebronco.com/forum/57-78-96-build-forum-builds-only/)
-   -   Mongomann75's 85 Build (https://www.fullsizebronco.com/forum/57-78-96-build-forum-builds-only/335545-mongomann75s-85-build.html)

MONGOMANN75 11-09-2014 10:37 PM

Mongomann75's 85 Build
 
Western PA winters bring with them snow and cold. Last year I found myself plowing more then I wanted with my 1999 F350 4 door 8 foot bed. Too long to be able to get around some of the areas I plow. I decided to do something about it.
I started looking for a early 80's Bronco, IMO these are the best looking Fords ever! After going thru the normal issues from craigslist I found someone willing to barter for his 85! I made the deal, drove it home an then to work for the next week for a good shake down.
I knew there would be rot, I mean its 30 years old! But I needed to pay a little better attention, I found about 2 gallons of Putty and at least 6 tubes of painters caulk and aluminum flashing hiding lots of the ugly stuff.
I plan to do the following to the 85,
1. SAS D60 on leaves using 1ton pieces
2. 10.25 in the rear with the proper springs
3. Fix the rust right. Daddy always said if your gonna do it do it right......
4. Pull all the interior and bed liner the inside
5. Paint the exterior in a fancy OD or FDR with BOSS stripes
6. Fabricate custom bumpers winch up front and spare tire carrier in the rear
7. Remove any unnecessary item from the ride, if I don't need it, its gone
8. Full tune up, all fluids, filters, etc.......
9. Teach my 10 year old son all about the world of wrenching.......
10. Have fun with it.

I will post up pictures as soon as I load them! Ideas and thoughts are welcome I appreciate educated conversation about these things, I like to learn from others experiences and hope to be able to return the favor to the community. Thank you for your time!

jopes 11-09-2014 10:53 PM

Sounds like you have alot planned for the build. I would probably set the suspension up so the bronco sits level, that way when you put a plow on it the front's going to go down some.

There is a SAS forum on here and a good many have done front leaf springs so you can get ideas from their builds as well.

MONGOMANN75 11-09-2014 11:01 PM

I have been lurking on the SAS side looking at the way everyone is swapping over! I am looking at using the stock front frame horns from the F350 with the shackles in the front. I drove the truck that the frame came from and did not mind the backwards spring flex as compared to my super duty! Still up in the air about it all thou.

MONGOMANN75 11-09-2014 11:07 PM


jopes 11-09-2014 11:15 PM

man that cancer is bad.

Update your profile for your bronco information. Makes it easier for when you ask questions.

MONGOMANN75 11-10-2014 11:04 PM

Day 2
 
Let the cutting begin!http://i266.photobucket.com/albums/i...ps27e50a88.jpg
http://i266.photobucket.com/albums/i...ps874a0d10.jpg
http://i266.photobucket.com/albums/i...psd0bb846d.jpghttp://i266.photobucket.com/albums/i...psc8a095b6.jpg
[URL=http://s266.photobucket.com/user/mongomann75/media/IMG_7847_zpsc8a095b6.jpg.html][IMG]

http://i266.photobucket.com/albums/i...psf05eced7.jpg
http://i266.photobucket.com/albums/i...ps2464784b.jpg

http://i266.photobucket.com/albums/i...ps928378d6.jpg

Got the rotten rear cross member out and started to fab the new one! Hope to fix the frame and finish the cross member tomorrow! My son comtinued to grind away at the inside of the tub!

BikerPepe` 11-11-2014 03:04 AM

wow man. you've got a lot of work ahead of you. awesome to be making it a father/son kinda project.
we all gotta start somewhere... better a Bronco than something else. :thumbup

EJakobsen 11-11-2014 08:17 AM

My -82 is the same color and about the same rust to..
Will have to do the same thing you guys does soon, this will be followed so i can se how everything looks like.

:)

MONGOMANN75 11-17-2014 07:20 AM

Keep at it
 
Some more photos of the patches going in, up to 7 now with many more to go.
http://i266.photobucket.com/albums/i...ps19603ff9.jpg
http://i266.photobucket.com/albums/i...ps0c6c2bdf.jpg
http://i266.photobucket.com/albums/i...pseb754a7f.jpg
http://i266.photobucket.com/albums/i...ps7dd69968.jpg
http://i266.photobucket.com/albums/i...ps7dd69968.jpg
http://i266.photobucket.com/albums/i...ps1a53fdb5.jpg
http://i266.photobucket.com/albums/i...ps82ea8ea4.jpg
http://i266.photobucket.com/albums/i...psf9193ae0.jpg
http://i266.photobucket.com/albums/i...ps51ad8518.jpg
http://i266.photobucket.com/albums/i...psf0eab8de.jpg
http://i266.photobucket.com/albums/i...ps7943ad51.jpg
http://i266.photobucket.com/albums/i...ps68e5801e.jpg
http://i266.photobucket.com/albums/i...ps8f7aea7d.jpg
http://i266.photobucket.com/albums/i...psa766d7df.jpg

The last picture was cleaning it up at work before I started!

RAMPNT1 11-17-2014 11:15 AM

These are my favorite builds. I love seeing what some of you guys can do to save a Bronco.

MONGOMANN75 11-18-2014 07:15 AM

Seats
 
I have 8 of these buckets and am thinking about using them in the Bronco, they are all passenger side Sprinter seats. What do think?

http://i266.photobucket.com/albums/i...ps0f051d03.jpg

dundee27 11-18-2014 09:49 AM

man you done some serious work there . Looks good , glad you could save it.

MONGOMANN75 11-18-2014 11:46 AM

Quote:

Originally Posted by dundee27 (Post 4869673)
man you done some serious work there . Looks good , glad you could save it.

I am trying to save it, have not actually done it yet! The guys at work that are keeping track of the build have been calling it the Zombie Bronco, or Frankin Bronco because I have brought back from the dead! So far so good!

Saltlife 11-18-2014 12:15 PM

:popc1: wow :popc1:

exranger06 11-18-2014 01:54 PM

This thread is really inspring to me. My Bronco has a lot of rust too, pretty much just as bad as yours. I have to replace that rear crossmember on mine too. It's nice to know that it's fixable and my truck isn't too far gone. The only thing is, I can't do bodywork, so I have to get a body shop to do it for me.

MONGOMANN75 11-18-2014 04:11 PM

Body Work
 
Quote:

Originally Posted by exranger06 (Post 4870114)
This thread is really inspring to me. My Bronco has a lot of rust too, pretty much just as bad as yours. I have to replace that rear crossmember on mine too. It's nice to know that it's fixable and my truck isn't too far gone. The only thing is, I can't do bodywork, so I have to get a body shop to do it for me.

This is not what I would call body work. I am in the fab stage, this is what I love to do. I was seriously close to walking away from the truck but something in me loves the challenge of bringing something back to life! You have to get past the idea of having everything perfect to be able to cut the rear cross member out of your Bronco. It will never be the way it was but it will be better then it is! I am not going to use any mud on the truck at all! All welds will be left naked, I am going to paint it, just not concerned about it being perfect! I plan on adding several bumps and bruises to it myself so why make everything perfect in the beginning? I am glad this is inspiring you!

exranger06 11-18-2014 06:11 PM

Quote:

Originally Posted by MONGOMANN75 (Post 4870330)
This is not what I would call body work. I am in the fab stage, this is what I love to do. I was seriously close to walking away from the truck but something in me loves the challenge of bringing something back to life! You have to get past the idea of having everything perfect to be able to cut the rear cross member out of your Bronco. It will never be the way it was but it will be better then it is! I am not going to use any mud on the truck at all! All welds will be left naked, I am going to paint it, just not concerned about it being perfect! I plan on adding several bumps and bruises to it myself so why make everything perfect in the beginning? I am glad this is inspiring you!

Well whatever you want to call it, it's beyond my abilities. My Bronco is going to (hopefully) be perfect and back to brand-new condition when all the body work is done.

MONGOMANN75 11-18-2014 10:53 PM

Drivers Seat
 
Got the Drivers seat in it tonight!
http://i266.photobucket.com/albums/i...psd424fbe8.jpg
http://i266.photobucket.com/albums/i...ps2ed55329.jpg
http://i266.photobucket.com/albums/i...psac22e2d7.jpg
http://i266.photobucket.com/albums/i...psfc37a761.jpg
http://i266.photobucket.com/albums/i...ps952a4c39.jpg
http://i266.photobucket.com/albums/i...ps2b3d481d.jpg

I cut the top off of the Sprinter mount base and leveled it to the floor of the Bronco then welded it to the floor, still some small areas to weld up on it but for the most part I am very happy with the location it puts me in and the feel of it in the Bronco! The seat has seat belt attachment points on it, this will make the seat belt install a snap!

It was 12 degrees in the garage when I got there spent 2.5 hours there tonight, the first hour was directly in front of the torpedo heater!

MONGOMANN75 11-18-2014 10:56 PM

Quote:

Originally Posted by exranger06 (Post 4870650)
Well whatever you want to call it, it's beyond my abilities. My Bronco is going to (hopefully) be perfect and back to brand-new condition when all the body work is done.

I guess it could be body work, didn't mean to come off the wrong way. To date I have 21 hours in the total job from when it rolled into the garage!

MONGOMANN75 11-19-2014 10:29 PM

Bottom of The B Pillar
 
http://i266.photobucket.com/albums/i...ps4d7eb2f3.jpg
http://i266.photobucket.com/albums/i...ps8204f93d.jpg
http://i266.photobucket.com/albums/i...ps4183d522.jpg
http://i266.photobucket.com/albums/i...ps6fb0e92d.jpg
http://i266.photobucket.com/albums/i...pscb6da0f9.jpg
http://i266.photobucket.com/albums/i...psd3cb5721.jpg
http://i266.photobucket.com/albums/i...ps9e5512cc.jpg

Got most of the old out and put one good clean patch in! Total of 2 hours tonight! My son removed the remainder of the interior! The last picture takes me back to when I used to sit in a truck in the garage and dream about all the adventures I would have behind the wheel!


All times are GMT -4. The time now is 11:49 AM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

 
For the best viewing experience please update your browser to Google Chrome