Bronco Forum - Full Size Ford Bronco Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. 1980-'96 Bronco Tech
    Hello all, I recently bought a rebuilt 5.8 engine off my friend, it came out of an 89 Bronco with AOD trans, Its bored .03 over and crank undersize .01 sleeves. They got speed pro Hypereurectic Pistons. Im planning on putting this in my 94 bronco that also has a 5.8. My main Concern is Will the...
  2. Broncos for Sale!
    1993 Ford Bronco XLT Ready for your next project? Time to let the next enthusiast take the reigns on this one. I just don't have the resources now to take care of her. The interior is removed but I have everything. I started to lay down sound deadening material but that's as far as I got. New...
    $8,500 USD
  3. 1980-'96 Bronco Tech
    Hey all, looking for some advice on an issue. My 92 5.8 bronco is running into a persistent issue that I cannot seem to solve. Ive replaced: FPR Fuel filter EGR Evr Evp Purge canister Tps ECT Vacuum lines(excluding the hvac ones) I can drive for 15/20 minutes with the engine cold and it run...
  4. 1980-'96 Bronco Tech
    I’ve had this issue where my bronco idles high in park. When I start it up I let it idle down which takes about a minute, it goes from about 900 rpm down to 500 which is normal. Then I go drive it for about an half an hour and park it it jump from 500 to about 1100 rpm. I wouldn’t think it’s a...
  5. 1980-'96 Bronco Tech
    Hey everyone, I’m trying to track down an issue with my 92 5.8 Bronco. occasionally while driving highway speeds, I’ll get a sudden loss of power(feeling like running out of gas) and a random knock that sounds like it’s coming from the driver side front wheel well. When it happens I’ll usually...
  6. Noobie Bronco Tech Questions. Flame free zone!
    94 XLT 5.8 Bronco Hey yall, so as I’m driving my check engine light will pop on and eventually after a few seconds to minutes will go away sometimes not coming back for the rest of the drive, sometimes it does. Seems to come off sometimes when coming to a stop at a light or just while driving...
  7. 1980-'96 Bronco Tech
    Hi guys, I’ve been have a few problems with the ole 91 bronco. It has the 5.8 351w. So when you’re at a stop and you accelerate, from about 15-45 the whole car vibrates like crazy. Anything before that and after that is smooth. I replaced the axle pivot bushings and the trans mount yesterday...
  8. 1980-'96 Bronco Tech
    351w auto issue I’m having is at idle it runs good. Around 700rpm and pretty smooth. If you give it just about any throttle it will misfire/buck. While driving it will buck really hard with just about any throttle. I’ve messed around with it a bunch and haven’t figured it out yet. Please help...
  9. Noobie Bronco Tech Questions. Flame free zone!
    I have another thread going on my trials and tribulations with the current engine removal/overhaul/installation on my son's 1995 5.8 XLT Bronco. https://www.fullsizebronco.com/threads/351w-first-engine-rebuild-overhaul.525236/ The engine is back in the engine bay and I'm hoping to get...
  10. 1980-'96 Bronco Tech
    So, got my 1996 Ford bronco 5.8L back from the Mechanic's for a broken water pump bolt (yeah that one) and a thermostat replacement among a few other things. Now the gauge, after a few minutes, decides to flicker and stays all the way stuck to the left. The big problem is the notable clicking...
  11. 1980-'96 Bronco Tech
    Hey guys, I just achieved 13.9 MPG at my last fill-up on the Bronc'. I started out around 11 MPG when I bought it STOCK in 2020. This is all based on an average mix of city/highway driving and alternating between grandma driving and race car driving, haha. The truck now has 157k miles on it, a...
  12. Introductions
    New to the forum, and my bronco has a special story behind it. About 20 years ago, my late father in law bought a 1984 with the 5.8/351 engine. He was terrible with cars, but was the biggest Boise State Broncos fan imaginable. He painted his Bronco blue and orange , with Bronco logos and GO...
  13. Want to buy Parts/Accessories/Misc other items
    Looking for a stock throttle body (F4TZ9E926C) for my 94 5.8. Will pay via Paypal including the shipping cost.
  14. 1980-'96 Bronco Tech
    Howdy folks! So I just did a big job last month on my '96 Bronc' with the 351W. Water pump, timing cover, timing chain, harmonic balancer. Put quite a few miles on the thing since the repair and found no leaks (praise the lord, right?). Well just a couple days ago I noticed the dang thing is...
  15. 1980-'96 Bronco Tech
    alright guys here it goes. I got a 87 bronco 5.8L 351w carb. So recently I took carb apart cleaned it out replaced gaskets and so on ya know the kit comes with. Well I also went ahead and replaced the fuel filter that’s going from my fuel filter that’s connected to motor near oil filter it’s a...
  16. 1980-'96 Bronco Tech
    Having issues with shifting 1st hard into 2nd won't shift into 3rd unless it's at almost 5000rpms just started smelling like it's burning and reverse is hard shifting now and has started idling high as well. This was my dad's old bronco that was left to me when he passed and I'm trying to fix it...
  17. Noobie Bronco Tech Questions. Flame free zone!
    Hi guys! I’ve been lurking a bit, I think it’s time for me to go legit. So, been ring shopping for the girl (also time to make that legit) and I jokingly said “you get a diamond, what do I get!?” and she hits me back with “well I’ve been thinking about that, and I think I’ll buy you the old...
  18. Noobie Bronco Tech Questions. Flame free zone!
    Gotta replace the exhaust system, Midas quoted me like $3000 so I figured I’d try and do it myself first. This is a project truck after all. So I’m looking on bronco graveyard and of course they don’t have any exhaust systems that say “5.8” in the title, only 4.9 and 5.0. I’m looking at this...
  19. Noobie Bronco Tech Questions. Flame free zone!
    Planning on putting the bassani Y pipe with no cats on my truck. I know I have to weld a bung on for the downstream O2 sensor but I was wondering if anyone had a link to a MIL eliminator or bypass of some sort for it? I can’t seem to find any and I just don’t want to get an engine code from it...
1-20 of 28 Results
Top