Bronco Forum - Full Size Ford Bronco Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 20 Results
  1. Noobie Bronco Tech Questions. Flame free zone!
    I just bought an 89 eddie bauer. They did a swap with a 351 small block. He told me that the o2 sensor needed replaced to fix the running rough and after I replaced the sensor it still runs rough. I tried to clear the memory but nothing seems to have happened. Any tips?
  2. 1980-'96 Bronco Tech
    Hi, I don't know a lot about mechanics but I have an 5.0L '89 Eddie Bauer Bronco that's been in the family for 3 generations now and means the world to me. I need to replace my engine because it recently blew after constantly burning/leaking both oil and coolant. I'm looking to replace it with...
  3. 1980-'96 Bronco Tech
    Hi everyone, Before I start outlining my problem, please know that I nearly read every thread on this forum about engines stalling in Broncos. I just got my Bronco back from a shop and $4k dollars later...I still have the same problem. Here we go: My 1993 Ford Bronco XLT 5.8l has rebuilt...
  4. Noobie Bronco Tech Questions. Flame free zone!
    Recently purchase a 1992 bronco that my Wife and Baby daughter will use as a fun vehicle, I have spent a tremendous amount of time trying to get it to run as it should and as best as it did the first time I drove it, It has a problem where it will operate decently until it gets warm when it does...
  5. Dixie Chapter
    Hi, can anyone recommend an engine machine shop and/or a transmission shop in the Huntsville AL area? I'm just rebuilding a stock engine. Thanks
  6. 1980-'96 Bronco Tech
    Not sure if this is the right place for this but what would anyone think about a 3v 4.6 forged bottom end with a procharger swapped in my bronco? I wanna do something different and I don’t really like the 4v modular engines cause the sound just doesn’t fit in my opinion. Ik it would be a pain in...
  7. Noobie Bronco Tech Questions. Flame free zone!
    So I've been trying to diagnose my 92 bronco. I recently put a new 5.0 engine and new exhaust system but I'm getting slight throttle hesitation. The engine will want to die the sputter to life after slamming the throttle but if you go into the throttle slow it's fine. I checked the fuel...
  8. Noobie Bronco Tech Questions. Flame free zone!
    Does anyone live in San Diego county? I am having engine hesitation issues with my new crate engine. Looking to get some help on possibly diagnosing the problem if anyone is willing to. If not does anyone know a good mechanic that specifically works on or has a lot of experience with ford...
  9. Noobie Bronco Tech Questions. Flame free zone!
    Hey everyone. My 94 EB w/351w now has enough problems that it's probably time to get the motor rebuilt. Having the oil pump go out while needing a rear main seal oln a motor with 230k on it is a good sign. Any recommendations for a shop in Denver? Thanks!
  10. Noobie Bronco Tech Questions. Flame free zone!
    So I have a 89 Bronco that has sat since 2013. It won’t turn on. The last time it turned on was in 2015. When we stopped using it, it needed a complete engine rebuild. I’m trying to figure out about how much it would cost to get it running again. Any help?
  11. Noobie Bronco Tech Questions. Flame free zone!
    I recently got an 83 bronco with a 302, everything seems pretty stock under the hood. They said it had a carb issue, but it looks like it was just a faulty fuel pump that was leaking. I updated the ignition coil, fuel pump, plugs, wires & distributor cap. I'm looking at swapping the 2 barrel out...
  12. Noobie Bronco Tech Questions. Flame free zone!
    This is between the battery and the firewall on my ‘94 Bronco EB 5.8L What is this hose in red? Should it be hose clamped, it keeps coming off under power? What is the small canister in blue? There is nothing on the other side of the small canister (green), looks like another hose would fit...
  13. 1980-'96 Bronco Tech
    My rpm gauge hasn’t worked since I bought my bronco and I’m trying to figure out how it works. Also under the hood on the driver side there is some wires not plugged in to anything and there is another wire coming out of the harness beside the distributor that is red/orange and has a blue...
  14. West Coast Chapter
    Hi My 1990 Bronco is in need of a full Transmission overhaul and possibly an engine overhaul as well. Anyone know of a good place in the San Fernando valley area that knows what they are doing with these? Thanks in advance
  15. 1980-'96 Bronco Tech
    I just pulled the engine to replace the oil pan gasket, timing chain cover gasket, water pump gasket, oil pressure sensor, manifold gasket, upper manifold gasket, valve covers gaskets, etc. Basically took the whole thing apart and put back together with new gaskets. Something is misfiring though...
  16. 1980-'96 Bronco Tech
    Hello! I started the bronco this morning and noticed a fire type smell, I shut the car off and lifted the hood to notice smoke coming from the area shown in the pictures. Any ideas?
  17. 1980-'96 Bronco Tech
    Hello! When turning the key to the on position, you can hear the fuel pump prime for two seconds like it always does but today I noticed it sounds like its constantly running while the engine is on. I’ve never heard it do that before. It sounds like it’s whining; it’s not very loud but you can...
  18. Discuss the 2021+ Bronco Here
    Ford Performance is offering a tune for for the 2.3L 4-cylinder engine that's in the Ranger and (soon to be) the Bronco. For $825 it increases the power from 270 horsepower and 310 lb-ft of torque to 320 horsepower and 355 lb-ft of torque. The package also includes a high-flow K&N air filter...
  19. Blog
    Bronco Generations 1st Generation – *1966-1977 2nd Generation – 1978-1979 3rd Generation – 1980-1986 4th Generation – 1987-1991 5th Generation – 1992-1996* * First Bronco made in August 1965 * Last Bronco made in June 1996 Bronco Engines 170 I6 (2.8L) – 1966-1972 200 I6 (3.3L) – 1973-1974...
  20. West Coast Chapter
    Hello, can anybody out there help me fixing up my Bronco, don't have the place and tools. I'm in L.A. so anybody who is a good mechanic and can take care about my Bronco, please write or call. 575-405-8983 thanks wolf
1-20 of 20 Results