Bronco Forum - Full Size Ford Bronco Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 24 Results
  1. Noobie Bronco Tech Questions. Flame free zone!
    Hello everyone Looking to tapings the wealth of knowledge that this place has. I'm rebuilding my 88 bronco with a 94 roller lifter engine. First time doing a rebuild and engine So I was cleaning my cam and I noticed a grove worn from the roller lifter on the lobe . I cleaned it up and can feel...
  2. 1980-'96 Bronco Tech
    Sup fellas - Bought my first old bronco about 7 months ago and it’s been a rollercoaster to bring this thing to her former glory. 91 Bronco XLT. There’s been two extended trips to the family mechanic already, one saw a brand new engine put in it (prev owner tried to repair the block with JBW -...
  3. 1980-'96 Bronco Tech
    Hello- long time reader, but first time poster. I have a 96 FSB. A couple months ago I noticed a sloshing sound coming from the front passenger side of the vehicle mainly the first couple of minutes when I start driving it. I took it to the shop that I have work on my bronco and they replaced...
  4. Noobie Bronco Tech Questions. Flame free zone!
    I have a 92 Bronco and I’m having an issue. There’s an audible front end clunk that happens randomly at random speeds. While clunking it causes the brake pedal to pulsate up and down. Everything in the front end is tight and the entire brake system has been bled religiously. The hubs are...
  5. 1980-'96 Bronco Tech
    I have a 93 Bronco that lately has started to sputter once I’ve been driving her for a bit and she’s warmed up, the longer you drive at that point it starts to get worse until you give it gas and it stops moving, sputters and dies. If it’s not too hot yet you can either try and accelerate...
  6. Noobie Bronco Tech Questions. Flame free zone!
    I have a 1990 bronco with a 331 stroker and the micro fuel pump on the frame went out while driving it. I have to wire the pump directly to the battery to get it off the road to where I was going. I have now fixed the electrical problem with the pump and everything is wired as it should be but...
  7. Ford Bronco Pickup Truck Discussions
    Hey All. New user looking for some advice because I’m out of ideas. I have a 92 that is a push button 4x4 with manual hubs. I’ve recently replaced bearings, calipers, and hubs. I’ve got a light clicking coming from left front hub in 2wd. When you Jack it up you can’t hear any clicking and...
  8. Noobie Bronco Tech Questions. Flame free zone!
    So I have a 96 bronco with a 351 and E4OD. The trans would shift very rough and after about a month the OD light started to sporadically flicker, and the speedo and odometer stopped working. A few days later the transmission would not shift out of first. It was not throwing any codes at the...
  9. Noobie Bronco Tech Questions. Flame free zone!
    Trying to figure out what that grey connector plugs into
  10. 1980-'96 Bronco Tech
    I don’t know what to do at this point. One day I go to warm up the 95 bronco and it didn’t start, it made the clicking noise when I tried to turn it over. First thing I did was check the relay on the fender. It was pretty old so I figured might as well change it out. Still the click. So I...
  11. 1980-'96 Bronco Tech
    I have an 87' bronco and currently trying to remove the seatbelt to get them re-webbed (they are a cut up mess) and i run into a snag... laterally. there's a green cable connected to the spool that seems to be connected to the door frame to a plunger type thing on the left of the image. Any...
  12. Noobie Bronco Tech Questions. Flame free zone!
    So I have a 1995 Ford bronco 5.8L and i changed the fuel filter and cleaned my intake to see if that’s the problem. I pulled the codes and only 536 popped up but I cleared and hasn’t come back. thanks Jarrett
  13. Noobie Bronco Tech Questions. Flame free zone!
    I have an 86 302 EFI that I have been working on and one of the things I wanted to check was timing, so I bought a timing light. Hooked it up to the #1 wire, disconnected the spout connector, marked 10 degrees BTC on the damper and started the truck. Readings showed more like 20+ BTC (just a...
  14. Noobie Bronco Tech Questions. Flame free zone!
    I have an 86 302 EFI that I have been working on and one of the things I wanted to check was timing, so I bought a timing light. Hooked it up to the #1 wire, disconnected the spout connector, marked 10 degrees BTC on the damper and started the truck. Readings showed more like 20+ BTC (just a...
  15. Noobie Bronco Tech Questions. Flame free zone!
    I'm a first car owner at the age of 21 and don't know much about fixing cars and decided to throw myself into the deep end and get a used bronco 2 XLT(1987) understanding all the issues it will have. it worked fine but had a lot of "quirks". Let me paint the scene: Bought the truck knowing a few...
  16. Noobie Bronco Tech Questions. Flame free zone!
    Take it for a drive for about 15 minutes around town so it can relearn idle strategies and shifting patterns. Then see if it still gives you trouble.
  17. West Coast Chapter
    I got Handed down my grandpas 86 XLX Bronco 2. I dont where to start its a bit beaten down (could be worse mainly just paint and interior) would it be a nice 4 wheeler car.. what are its pros and cons. of this vehicle its weak points. and strong point
  18. 1980-'96 Bronco Tech
    Hi I have a 1991 ford bronco xlt with a 4 inch rough country lift kit. A couple years ago me and my dad broke our stock drive shaft and we were wondering since we have a lift kit on it do we need a different sized drive shaft because it is lifted and if so what size drive shaft should we get...
  19. 1980-'96 Bronco Tech
    Hey guys I'm new to the bronco community I got my dad's old 1991 xlt bronco as my first car for my 17th birthday, and it has a problem with there's a rear drive shaft and I need help trying to figure out what size is it. I will be thankful for any help I can get. Info on truck 1991 xlt ford...
1-19 of 24 Results
Top