Bronco Forum - Full Size Ford Bronco Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-10 of 10 Results
  1. 1978-'79 Bronco Tech
    I recently replaced all the vacuum lines under the hood. I also replaced the EGR valve, position sensor, and solenoid. I have no check engine lights on and no OBD codes. In the morning (around 50 degrees F), I hear an intermittent noise that sounds like a actuator cycling. Kind of a BERMP...
  2. Noobie Bronco Tech Questions. Flame free zone!
    Having startup issues with a 1994 Bronco with the 5.8 and E4OD. Recently let the truck sit for about two weeks after performing some work with the doors / lights on. Battery seemed to drain and wouldn't start, so I jumped it using an external battery pack on the terminals. Fired up shortly...
  3. 1980-'96 Bronco Tech
    Hi! I was wondering if anyone could help me pinpoint the source of some new issues I'm having with my Bronco. Or if anyone else has experienced similar issues. 91 Bronco 5.0L V8 E40D Transmission 147K miles Initially, it was throwing a 629 check engine code: converter clutch solenoid circuit...
  4. Noobie Bronco Tech Questions. Flame free zone!
    Hey guys, I have a '94 5.0 Full Size Bronco. Looking for a part number for the wiring that goes from the Starter Relay (solenoid) to the Starter. In particular the ground. I have some corroded (27 year old) wires. It is causing it to short out. I've done some research on my own, but can't...
  5. Noobie Bronco Tech Questions. Flame free zone!
    So....I have an 89 Bronco EB that won't start with the key. When I purchased a few weeks ago, seller said solenoid most likely needs replaced. Well before I did anything, I used the screwdriver across the terminals of the starter solenoid and it fired right up. After replacing the starter...
  6. 1980-'96 Bronco Tech
    Got a 95 XLT 5.8L Got a CEL the other day after about 3 miles. Same thing everytime. Start it up and nothing. Drive a few miles and it’s on. Pulled the KOEO codes and got 629 - converter clutch solenoid circuit fault or lock up solenoid cir 622 - shift solenoid 2 circuit failure koeo 558 -...
  7. Noobie Bronco Tech Questions. Flame free zone!
    I posted a thread just a bit ago. My tcc solenoid is not working so I guess it’s time for a new solenoid pack. I have a WAY1 eec and am wondering what solenoid to use. This is the one I have. To me it looks like it has the new style plug however has diodes in place. Did someone just change the...
  8. 1980-'96 Bronco Tech
    so after doing EVERYTHING! to stop sticking into 2nd gear, tps, instrument cluster, fluid change and additive, it still has the same problem. From what my work colleagues say, 2nd-3rd clutch in the transmission might be gone or extremely worn. When changing the fluids it had a very pungent...
  9. Noobie Bronco Tech Questions. Flame free zone!
    I have a ground loop going to the hot Red/Light Blue wire on the fender Solenoid. I do not get 12v when turning the key. I thought the output R/L-B from the ignition switch was bad but it is not. Solenoid works otherwise if I jump it out or across the two posts. The only other point in the...
  10. Blog
    Over the years, your old Direct Drive OEM Starter has probably been very reliable. These starters utilize a large field coil to create a magnetic field which moves the drive gear into contact with the flywheel. But eventually you probably have found several performance issues that may have...
1-10 of 10 Results
Top