Bronco Forum - Full Size Ford Bronco Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-13 of 13 Results
  1. 1980-'96 Bronco Tech
    How To Remove And Install OBS Ford Truck / Bronco Steering Column 92-96 F150 F250 F350
  2. Noobie Bronco Tech Questions. Flame free zone!
    Hey everybody, I need some help. About a year ago I did a motor swap in my 1992 Bronco. During the motor swap I went ahead and replaced the old steering gear with a new one. At the same time, I replaced all the steering arms and tie rod ends. I removed all the old steering arms and laid them on...
  3. Noobie Bronco Tech Questions. Flame free zone!
    I have a 1995 bronco that runs great but steers like a nightmare, as if the steering wheel has very little control over the tires. Makes driving over 60 on a backroad feel extremely unsafe. So far I have -redhead steering gearbox -borgesson steering shaft -new tie rods, tie rod ends -just had...
  4. 1980-'96 Bronco Tech
    So I've been trying to figure this problem out and I am fed up. My 94 Bronco 5.0 w/ e4od and 4wabs has been having a steering issue for a couple months. Its a lot to explain so bear with me. When driving and turning, the steering will randomly and aggressively start to pull to the left. The...
  5. Noobie Bronco Tech Questions. Flame free zone!
    1989 Bronco EB, 5.0 automatic w/ Tilt Okay so This has been a long project. -Front end steering / suspension rebuild -alignment performed at shop **steering wheel play still present -installed new redhead, rag joint, and power steering pump. When I primed the box (back&forth a bazillion...
  6. 1980-'96 Bronco Tech
    Was hoping you could help a fellow bronco owner out as I know you all are the best people and most knowledgeable about all Broncos. I have a 95 xlt with a 2.5 rough country lift (please don’t judge) but my steering is very loose and there’s give in the steering. What can tighten my steering up...
  7. Noobie Bronco Tech Questions. Flame free zone!
    Hi folks, I'm new on this forum. I own a 1996 E250 4x4 originally converted by Quigley in PA. They put on a Bronco front axel with a 3 inch lift kit when the truck had 60 miles in 1996. I own the truck since 2010. The truck was in Alaska and Yukon before I bought it. I beleive the actual...
  8. Noobie Bronco Tech Questions. Flame free zone!
    So there has been an unusual amount of play in my steering wheel. So I researched here and worked my way down the steering column. -upper steering knuckle was tight -lower connection with the spring and plastic bracket was tight. -rag joint was solid -no wobble in the gearbox to frame...
  9. 1980-'96 Bronco Tech
    I’ve done wheel bearings, ball joints, tie rods twice, radius arm bushings, shocks and springs, steering box, and replaced rag joint with flaming river joint. My bronco started riding rough and the steering gets loose going over bumps and jerks a little and sometimes it gets tight turning around...
  10. Noobie Bronco Tech Questions. Flame free zone!
    G’day! I have a 1985 XLT all original and have been navigating repairs since early this year. I have a business in the US and before Covid spent a few months a year there, so chose the car knowing I’d be able to pick up parts on my travels easily and bring them back to Australia. The challenge...
  11. Blog
    So I finally fixed my steering issue. I ended up pulling the knuckles off and making sure the camber bushings were seated in correctly. Then i put the knuckles back on using the correct torque specs and it drives like a dream. Now i need to go back to the alignment shop and let them know that i...
  12. Blog
    I recently had the opportunity to stop by Red-Head Steering Gears in Seattle and meet with owner Harvey Foster. I found Harvey to be a very friendly person that was extremely knowledgeable and experienced with steering gears of all types. He was surprisingly more than willing to spend time...
  13. 1980-'96 Bronco Tech
    i have an 89 bronco eddie bauer ed. 4x4 fullsize with the 302. the frame on the side where the steering box has rusted out so the steering box is moving freely and going inside the frame and broke the bolts because of the slack , i was wondering if i can i get a machine shop to fab me up a plate...
1-13 of 13 Results
Top