Bronco Forum - Full Size Ford Bronco Forum banner

Status
Not open for further replies.
1 - 19 of 19 Posts

·
Cadillac of Men
Joined
·
3,787 Posts
Discussion Starter #1
I got some stuff I want to get rid of before the snow.

3 Front Driveshafts w/ CV's (78-79) $20 each
NP435 4spd manual trans, needs rebuild $50
C6, 2wd, SB bellhousing, needs rebuild $50
NP205, good shape, ready to run $150
Dana 44 solid front axle, missing most of right side $SOLD
Dana 44 solid front axle, complete $200
Ford 9" rear end, complete newish $100
2 78/79 Factory Rollbars $20 each
Running boards off a 98 150 ext cab $Free
4" lift coils and blocks (new, unknown brand, 78-79) $50
4" lift coils (used, skyjacker, 78-79) $30

Plus a couple diff parts trucks, if you need anything, just ask, may have it, will sell cheap.

I am in Farmington, CT 06032.
 

·
Cadillac of Men
Joined
·
3,787 Posts
Discussion Starter #5
94_chickentaco said:
is this disc to disc?
yes, the steering and suspension are available as well.

muddinmike said:
hey what brand are the coils? how much would shipping run me to boise id 83702- comercial addy. I dont need the blocks either.

Thanks
I have 2 sets of coils, one is new unknown brand (red coil, maybe skyjacker) and the other is used and skyjacker. Ill check on shipping tomorrow.

Berne said:
got a 78-79 steering box you wanna get rid of?

--Berne
sure.
 

·
Registered
Joined
·
1,317 Posts
Yeah, I need something---A D44 Diff cover :D
 

·
scrounger extrordinaire
Joined
·
4,775 Posts
i just want to see if the blocks are 4"? & man i want a roll bar but i am in kansas. are you close to a forward air terminal?
 

·
Registered
Joined
·
145 Posts
Crazed said:
I may be interested in the 78-9 lift also...I am in portland
we are about 3,000 miles from you there tim. I wish i had 200 for that axle, if i hadn't already ready to order 1800 worth of stuff for my race quad. IM in CT too so it would of been nice.
 

·
Cadillac of Men
Joined
·
3,787 Posts
Discussion Starter #10
axaviere said:
i just want to see if the blocks are 4"? & man i want a roll bar but i am in kansas. are you close to a forward air terminal?
Yes I am. And I think the blocks are about 3" or 4" tall. I will check.

Crazed said:
I may be interested in the 78-9 lift also...I am in portland
Area code?
 

·
Cadillac of Men
Joined
·
3,787 Posts
Discussion Starter #14
Berne said:
Squatty...

look into shipping that steering box and the suspension (for Tim) to a buisness address @ 97132...I'll be cheapest to ship it here, and I can get it to Tim....he's just up the road...

and PM me what your thinkin' for a price for that box...

--Berne
ok, will do.

BlkBronco said:
Would you happen to have a rear driveshaft that would fit a 95?
sorry, no.

Broncot said:
The NP435-is it from a divorced transfer case?
What's missing exactly off the right side of the $50 Dana 44?
no, it was mated to an np205 in a 79 bronco.
the entire dana 44 is no missing because it is sold. sorry.
 

·
Registered
Joined
·
769 Posts
would a 78 factory roll-bar work in a 80' with little rigging? how much would it be for shipping to duluth MN 55804
 

·
Cadillac of Men
Joined
·
3,787 Posts
Discussion Starter #16
BucKinBroNcO said:
would a 78 factory roll-bar work in a 80' with little rigging? how much would it be for shipping to duluth MN 55804
it will prob fit with no problems at all. shipping will prob be quite a bit, just because of the size of the main hoop.


it will have to be monday for the shipping quotes requested. I work all day sat/sun so I dont have time to get dimensions/weights, and quotes. please be patient.
 
1 - 19 of 19 Posts
Status
Not open for further replies.
Top