Bronco Forum - Full Size Ford Bronco Forum banner

1 - 20 of 25 Posts

·
Registered
Joined
·
199 Posts
Discussion Starter #1
Michigan - Final part out before boneyard, 90 FSB XLT

--------------------------------------------------------------------------------



Parts/Bronco, located in Ypsilanti, MI, Ann Arbor

Prefer local sales cash talks
interior door panels, XLT, red, good shape, $125 pair
Frame mounted receiver hitch -$40-
Red back seat -$20, all the brackets-
Wiper linkages-$30
Inside spare tire carrier and cover, decent shape-SOLD
Steering gear box, frame mounted-SOLD
Interior trim panels- $10 each, red
dash switches-$5-10 each depending.......
window door glass-$15
Heater box with core, underhood, etc-$20
Vent windows pass good shape -$20
vent window driver side, good glass-SOLD
door window motors with regulators-SOLD
tailgate regulator-$100
tailgate wiring- newer 2 yrs old, $125
soft top is sold
axles, larger parts in other thread.
Still have T-case, electric shift-$200
gas tank loaded, -$50
headers-SOLD
red dashboard-$20
stock spare tire-$20
driveshafts - $50 each, rear is sold
radiator, looks good, few yrs old- SOLD
AC compressor-$30
tailights -Sold
headliner -$20 red, clean
front seats, center console, column gone
9" rear, 4.10, Detroit Tru-trac, $700-have deposit on it
D44 front, 4.10, LSD, 3rd member sold
Parting D44, $50 per spindle
Hubs, manual, Milemarker stainless $60 shipped
no wheels/tires available
Just trying to get crap out of the body before scrapping for sheet metal.

Prefer not to ship, don't ask for shipping estimates, if your interested you can figure out about what shipping would be. I'll try not to mark up much if any on shipping, but trying to avoid packing this crap up. Shipping from 48198 Zip Code
__________________
 

·
Registered
1996 Bronco 5.0/E4OD/BW1356
Joined
·
1,518 Posts
Is it a manual shift 1356? I am in need of the shifter...
 

·
Registered
Joined
·
199 Posts
Discussion Starter #3
Electronic shift 1356, sorry.
 

·
Registered
Joined
·
199 Posts
Discussion Starter #6
Sorry no longer have stock wheels with caps. Have a set of 15x8" Aluminum "gamblers" need polishing, no curb rash, $125 for all 4. PM me.

D44 front is "rotor to rotor" all new about 10-15K miles built by Rieder Racing in Taylor, 4.10 gears front/rear.
 

·
F.O.T.M. - MAY 2014!!!
Joined
·
6,250 Posts
Can I see a pic of the tailights? If they are in good condition I would like to get them ....
 

·
Registered
Joined
·
199 Posts
Discussion Starter #8
Sorry taillights are gone
 

·
Registered
Joined
·
199 Posts
Discussion Starter #9
If anyone's interested, I'd go $325 on the D44 3rd member. no extras.
 

·
Registered
Joined
·
199 Posts
Discussion Starter #12
Seats and brackets gone, sorry.
 

·
Registered
Joined
·
199 Posts
Discussion Starter #14
Replied to ya Newbie Ronco, Thanks!
 

·
Registered
Joined
·
199 Posts
Discussion Starter #15
Looks like 3rd member is sold, parting out rest of D44, axle shafts $35 each with newer u-joints, Milemarker stainless hubs with hardware to convert from Auto, $75, Spindles $50 per.

rotors,bearings, seals, calipers, matching pads, $40 per side. all newer except calipers with about 10-15K miles on them.
 

·
Registered
Joined
·
607 Posts
You still have the milemarker hubs?
Let me know if your in the mood to ship em?
Thx
D
 

·
Registered
Joined
·
199 Posts
Discussion Starter #17
Steering gearbox just went to Silver Bullet on Sat

Still have door glass, tailgate wiring, motor, electric Transfer Case(BW1356), red trim panels, dash, wiper arms complete assy, rear seat, 5.0 motor computer/harness(parting 5.0 out not complete), all wiring harnesses (frame/body), door 1/4 windows/frames, frame mounted receiver hitch

Manual hub conversions, milemarker stainless, good rotors/matching bearings, spindles(6 bolt)

9" rear new internals, 4.10 with Detroit Tru-trac, $700 firm

getting pretty well picked over at this point.

Maybe a couple things I've forgotten but not much
 

·
Registered
Joined
·
199 Posts
Discussion Starter #19
Skid plate went a while ago. Tank is free for the taking, seriously, I pulled it in Aug? with a little fuel in it, it's been sitting outside in the weather, at this point come get it........ PM me if interested.
 

·
Trying to finish it
Joined
·
1,355 Posts
is the ford 9" a complete axle? my area code 44266
 
1 - 20 of 25 Posts
Top