Bronco Forum - Full Size Ford Bronco Forum banner

1 - 20 of 37 Posts

·
Engineer
Joined
·
13,165 Posts
Discussion Starter #1 (Edited)
Wheelin' pics we've got mud again (video on page 2)

Went wheeling again yesterday after spending 2 days fixing my broken stub shaft, putting in my coil spacers, and replacing radius arm bushings

Before we headed out, Kyle hit up the front porch for some flex in the hoe

Me stuck on a hillclimb just short of the top


Zac leaning over, no pics of me in the same spot but the video should be up later when Ryan gets around to it

Stuck in a deep hole, The passengers fender took a beating there


A better pic from the front

The hole was really deep and got deeper as we comealonged back

And on the way home we did some more damage in the snow


There's another guy we were with that got more pics so I'll post those up later
 

·
Engineer
Joined
·
13,165 Posts
Discussion Starter #2
stangmata50l said:
Awesome pics.
The video's are pretty sweet we abused the Bronco pretty good. I cant wait to see the rest of the pics
 

·
Registered
Joined
·
327 Posts
Yeah, I'd say you were pretty stuck..... Cool pics.
 

·
Wrenching for a Livin'
Joined
·
6,950 Posts
johnski said:
That is one of the best stuck pics I've seen in a while. Nice job.:thumbup
I have to agree.

If thats your daily driver, you got some balls
 

·
Engineer
Joined
·
13,165 Posts
Discussion Starter #10 (Edited)
magnumpi said:
I have to agree.

If thats your daily driver, you got some balls
That's my daily driver, 7 miles each way to school everyday. Usually about 160 miles a week. So I'll have a late night in the garage this week putting in a new axle shaft again, but then again that's what I did Thursday night too. If anybody has a set of spare shafts for a D44 PM me.

Gtndrty said:
How about some pics of the inside?
I can just imagine how nasty the back looked afterwards.
I pulled the rear seat and the carpet, it's gonna get bedlined soon



bigbroncojeff said:
so how cold was that water.... i still see snow in places
Um maybe 35-40 degree water, hell it was only 40 degrees outside
 

·
Registered
Joined
·
1,647 Posts
Todd, do you have stock in Ford Parts? :toothless

Nice pics, and nice stick there.
 

·
Engineer
Joined
·
13,165 Posts
Discussion Starter #12
mcaldwell said:
Todd, do you have stock in Ford Parts? :toothless

Nice pics, and nice stick there.
Nope but I'd never pass up a good deal on a parts truck. I'm looking for a set of shafts now since my parts truck shaft only lasted 25 miles. I've got 3 D44 third members, I think I might weld one of them up and give that a shot see what it's like. I wish I had stock in spicer, at $30 a piece they're $$$ and of course that only lasted 25 miles. :doh0715:
 

·
Registered
Joined
·
1,078 Posts
bigbroncojeff said:
so how cold was that water.... i still see snow in places
It was a fun trip. The water was just above freezing, i know cuz i was standing in it working the highlift and hooking the straps and shackles. i couldnt feel my toes from like 1pm to 12am.
 

·
Engineer
Joined
·
13,165 Posts
Discussion Starter #15
stangmata50l said:
Todd, I think I have a spare set of axle shafts in my garage. I'll take a look tomorrow night and see what I can find.
That would kick ass. I'd take a stock stub shaft and slip yoke if you had it let me know what you want for it. I'd rather try to find a D50 stub shaft but getting it fixed is all that matters
 

·
Designated Tranny Killer
Joined
·
6,960 Posts
looks fun todd
 

·
Engineer
Joined
·
13,165 Posts
Discussion Starter #19
MikE2 said:
Sweet
You really put that Bronco through hell
Nah... only sometimes
 

·
Registered
Joined
·
1,011 Posts
Sweet pics. With all of the money you have been putting into parts, you should have upgraded to 3/4 ton running gear. :thumbup
 
1 - 20 of 37 Posts
Top